Setting Up Anynet
+
The following settings are to use Anynet
+
functions.
Scanning and Switching between Anynet
+
Devices
1 Press the TOOLS button.
➢
Then press the ENTER button to select Anynet+(HDMI-CEC).
2 Press the ▲ or ▼ button to select
Setup, then press the ENTER button.
3 If you cannot find a device you want, press the ▲ or ▼ button to select
Searching Connections, then press the ENTER button.
The message
Configuring Anynet
+
Connection... is displayed.
When searching devices completes, the connected devices are listed in the
Anynet+ menu.
To use the Anynet
+
Function, Anynet
+
(HDMI-CEC) must be set to On
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the ENTER button.
2 Press the ▲ or ▼ button to select Anynet
+
(HDMI-CEC), then press the
ENTER button.
3 Press the ▲ or ▼ button to select Setup, then press the ENTER button.
4 Press the ENTER button to select Anynet+ (HDMI-CEC).
5
Press the ▲ or ▼ button to select On, then press the ENTER button.
➢
The Anynet
+
(HDMI-CEC) function is enabled.
➢
If you select Off, Anynet
+
(HDMI-CEC) is disabled.
➢
When the Anynet
+
(HDMI-CEC) function is disabled, all the Anynet
+
related
operations are deactivated.
Setting an Anynet
+
Device to turn Off Automatically when the TV is Turned Off
4
Press the ▲ or ▼ button to select Auto Turn Off, then press the ENTER button.
5
Press the ▲ or ▼ button to select Yes, then press the ENTER button.
➢
The Auto turn off function is enabled.
➢
If you select No, the Auto turn off function is canceled.
Press the
EXIT button to exit.
➢
The Select Device setting of the TV remote control is to be set to TV to use the Anynet
+
function.
➢
If you set Auto Turn Off to Yes, connected external devices are also turned off when the TV is turned off.
However, if the device is recording, it may not be turned off.
➢
Switching to the selected devices may take up to 2 minutes. You cannot cancel the operation during the switching
operation.
➢
The time required to scan for devices is determined by the number of connected devices.
➢
When the device scan is complete, the number of found devices is not displayed.
➢
Although the TV automatically scans devices when it is turned on using the POWER button, devices connected when
the TV is already on are not displayed in the device list. In this case, select the Searching Connections menu to search
devices.
➢
If you have selected external AV device by pressing the SOURCE button, you cannot use the Anynet
+
function. Make
sure to switch to an Anynet
+
device by using the TOOLS button.
Setup
Anynet
+
(HDMI-CEC)
: Off
Auto Turn Off
: Off
Searching Connections
Enter ReturnMove
Off
On
Enter
Move
View TV
Select Device
►
Record
►
Menu on Device
►
Device Operation
►
Receiver :Off
►
Setup
►
TV Air 11
Return
Setup
Anynet
+
(HDMI-CEC)
: On
Auto Turn Off
: Off
Searching Connections
Enter ReturnMove
No
Yes
Setup
Anynet
+
(HDMI-CEC)
: On
►
Auto Turn Off
: Yes
►
Searching Connections
►
Enter ReturnMove
Enter
Move
View TV
Select Device
►
Record
►
Menu on Device
►
Device Operation
►
Receiver :Off
►
Setup
►
TV Air 11
Return
To Next Page
Loading...
