What to do if Samsung WD90K6410OW Washer does not drain and/or spin?
If your Samsung Washer isn't draining or spinning, ensure the drain hose is fully straightened to the drain system. Check the debris filter for clogs. Close the door and press Start/Pause. Make sure the drain hose isn't frozen or clogged, and that it's connected to a drain system that isn't clogged. Insufficient power can also temporarily prevent draining or spinning.
Why is my Samsung WD90K6410OW water supply insufficient, or no water is supplied?
If your Samsung Washer isn't supplying enough water, or not supplying water at all, fully open the water tap. Ensure the door is properly closed. Check that the water supply hose isn't frozen, kinked, or clogged. Also, confirm that there's sufficient water pressure.
What to do if the door does not open on my Samsung Washer?
If your Samsung Washer door won't open, press Start/Pause to stop the washing machine. Allow a few moments for the door lock mechanism to disengage. The door will not open until 3 minutes after the washer has stopped or the power is turned off. Ensure all water is drained from the drum. If water remains, drain the drum manually. Check that the door lock light is off.
Why is my Samsung WD90K6410OW Washer leaking water?
If your Samsung Washer is leaking water, ensure the door is properly closed and all hose connections are tight. Make sure the end of the drain hose is correctly inserted and secured to the drain system. Avoid overloading the washer. Use high efficiency (HE) detergent to prevent oversudsing.
How to reduce excessive suds in Samsung WD90K6410OW Washer?
If you notice excessive suds in your Samsung Washer, ensure the Auto Detergent and Auto Softener settings are configured correctly. Use the recommended types of detergent as appropriate, and opt for high efficiency (HE) detergent to prevent oversudsing. Reduce the detergent amount for soft water, small loads, or lightly soiled loads. Note that non-HE detergent is not recommended.
Why is the load wet at the end of a cycle in my Samsung WD90K6410OW Washer?
If your Samsung Washer load is still wet after a cycle, try using the High or Extra High spin speed. Use high efficiency (HE) detergent to reduce oversudsing. Be aware that small loads (one or two items) may become unbalanced and not spin completely. Also, make sure the drain hose is not kinked or clogged.
Why is my Samsung WD90K6410OW vibrating excessively or making noise?
If your Samsung Washer is vibrating excessively or making unusual noises, ensure it's installed on a level, solid, and non-slippery floor. Remove the shipping bolts. Make sure the washer isn't touching anything else. Check that the laundry load is balanced. Note that the motor can cause noise during normal operation, and metal objects like coins or metal-decorated clothes can also cause noise.
Why does my Samsung WD90K6410OW keep stopping?
If your Samsung Washer is stopping mid-cycle, ensure the power cord is plugged into a live electrical outlet. Check the fuse or reset the circuit breaker. Close the door and press Start/Pause. Be aware that before filling, the washer makes clicking noises to check the door lock and perform a quick drain. There may be a pause or soak period in the cycle, so wait briefly. Also, check the mesh filter of the water supply hose for clogs. Insufficient power can also cause the washer to temporarily stop draining or spinning.
Why does detergent remain in the detergent drawer of my Samsung WD90K6410OW after a cycle?
If, after a cycle, detergent remains in the detergent drawer of your Samsung Washer, ensure the washing machine is running with sufficient water pressure. Make sure the detergent is added to the center of the detergent drawer. Verify that the rinse cap is inserted properly. If using granular detergent, ensure the detergent selector is in the upper position. You may also need to remove the rinse cap and clean the detergent drawer.
Why is my Samsung WD90K6410OW filling with the wrong water temperature?
If your Samsung Washer is filling with the wrong water temperature, fully open both taps. Ensure the temperature selection is correct and the hoses are connected to the correct taps. Flush the water lines. Make sure the water heater is set to supply a minimum of 120 °F (49 °C) hot water at the tap. Disconnect the hoses and clean the mesh filter.
General| Type | Washer Dryer |
|---|---|
| Washing Capacity | 9 kg |
| Drying Capacity | 6 kg |
| Energy Efficiency Class | A |
| Energy Rating | A |
| Spin Speed | 1400 RPM |
| Color | White |
| Noise Level (Spinning) | 74 dB |
| Digital Inverter Motor | Yes |
| Eco Bubble Technology | Yes |
| Quick Wash | Yes |
| Delay Start | Yes |
| Child Lock | Yes |
| Dimensions (H x W x D) | 850 x 600 x 600 mm |
To Next Page