How to fix a Samsung WF42H5000AW/A2 that will not start?
If your Samsung Washer won't start, ensure the door is firmly closed, the washer is plugged in, and the water source faucets are open. Press the Start/Pause Button. Also, verify that the Child Lock is not activated and check the fuse or reset the circuit breaker. Note that before filling, the washer clicks to check the door lock and do a quick drain.
What to do if Samsung Washer shows unbalance error?
If your Samsung Washer displays an unbalance error, redistribute the laundry evenly.
What to do if my Samsung Washer stops mid-cycle?
If your Samsung Washer stops, make sure the power cord is plugged into a live electrical outlet. Check the fuse or reset the circuit breaker. Ensure the door is closed and press the Start/Pause Button. The washer won't tumble or spin unless the door is closed. Also, there may be a pause or soak period in the cycle, so wait and see if it restarts. Inspect the screens on the inlet hoses at the faucets for obstructions and clean them if needed. Note that before filling, the washer clicks to check the door lock and do a quick drain.
Why is my Samsung WF42H5000AW/A2 Washer vibrating or making noise?
If your Samsung Washer vibrates or is too noisy, make sure it is set on a level surface and that the shipping bolts have been removed. Ensure the washer is not touching any other object and that the laundry load is balanced.
What to do if my Samsung Washer has no water or not enough water?
If your Samsung Washer has no water or not enough water, first ensure that both faucets are fully turned on and the door is tightly closed. Check that the water inlet hoses are straight. If the hose filter screens are clogged, disconnect the hoses and clean the screens. You can also try opening and closing the door, then pressing the Start/Pause Button.
Why does my Samsung WF42H5000AW/A2 Washer show a drain error?
If your Samsung Washer displays a drain error, it could be due to several reasons. The pump motor impeller might be damaged internally and need replacement. Ensure the correct voltage is supplied to the parts. Inspect and replace any faulty parts. Freezing in the winter season can also cause this issue, so ensure proper winterization to prevent freezing. Additionally, the drain hose may be clogged, requiring you to clear the drain hose.
What to do if my Samsung WF42H5000AW/A2 Washer has a water supply error?
If your Samsung Washer is showing a water supply error, start by checking and cleaning the water supply valve, as foreign material may be entering it. Ensure the water supply valve terminal is securely connected. Verify that the warm water and rinse connectors are correctly connected to each other. Check and connect the PCB terminal from the drain hose to the detergent drawer, if it's disconnected. Inspect the transparent hose for any folds or tears and rectify the issue.
Why does my Samsung WF42H5000AW/A2 have detergent remains in the dispenser?
If detergent remains in the automatic dispenser of your Samsung Washer after the wash cycle, ensure the washer is running with sufficient water pressure. Also, make sure the Detergent Selector dial is in the upper position when using granular detergent.
What causes an overflow error on my Samsung WF42H5000AW/A2 Washer?
If your Samsung Washer is displaying an overflow error, inspect the water level detection system, as water may be supplied continually because it is not working correctly. Clear the drain hose, as a clogged drain hose with an injection error can also cause the water level detection to fail, leading to continuous water supply. Ensure the water supply valve is clear and not frozen, as these conditions can also cause continuous water supply. If the issue persists, inspect and replace the water level sensor if necessary, as it may be degraded.
How to fix motor driving error on Samsung WF42H5000AW/A2?
If your Samsung Washer displays a motor driving error or hall sensor error, ensure the PBA connector terminal is connected properly. Engage the motor spin net correctly. If the motor’s internal coil is damaged (short-circuited or cut), replace the damaged internal coil. Reconnect the hall sensor terminal if it is not connected. Also, check for any foreign material, such as a screw, that may have entered the motor and remove it.
Guidelines for choosing an installation site, covering electrical, grounding, and water needs.
Step-by-step guide for removing shipping bolts, selecting location, connecting hoses, leveling, and calibration.
Addresses issues like no start, no water, noise, stops, and wet loads with troubleshooting steps.
Explains error codes displayed by the washer and provides solutions or service guidance.
Details warranty coverage, terms, and exclusions for US customers.
Outlines warranty coverage, terms, and exclusions for Canadian customers.
General| Type | Front Load |
|---|---|
| Capacity | 4.2 cu. ft. |
| Color | White |
| Energy Star Certified | Yes |
| Spin Speed | 1200 RPM |
| Steam | No |
| Voltage | 120 V |
To Next Page
