To Next Page
C
Charles BryantAug 22, 2025
Why does my Samsung Washer show an unbalance error?
- SSharon TaylorAug 22, 2025
An unbalance error on your Samsung Washer is typically caused by the laundry load. Adjust the laundry load as needed.
Why does my Samsung Washer show an unbalance error?
An unbalance error on your Samsung Washer is typically caused by the laundry load. Adjust the laundry load as needed.
Why does my Samsung WF42H5200AF have a drain error?
A drain error in your Samsung washer can occur due to several reasons. It could be caused by a damaged pump motor impeller, supplying the wrong voltage to the parts, a part fault, freezing during winter, a clogged drain hose, or obstructions inside the drain pump assembly such as rubber bands, bills, cotton, hair pins, or coins. To resolve this, replace the pump motor impeller if damaged, ensure the correct voltage is supplied, replace any faulty parts, remove any freezing, clear the drain hose of any foreign materials, and clear any obstructions inside the drain pump assembly.
How to troubleshoot a Samsung WF42H5200AF with a water supply error?
To troubleshoot a water supply error on your Samsung washer, consider these potential causes: foreign material entering the water supply valve, a disconnected water supply valve terminal, incorrectly connected warm water and rinse connectors, a disconnected PCB terminal from the drain hose to the detergent drawer, or a folded or torn transparent hose. Try cleaning the water supply valve, reconnecting the water supply valve terminal, rearranging the warm and rinse connectors, connecting the PCB terminal, and inspecting the transparent hose for folds or tears.
Why does my Samsung WF42H5200AF show a power error?
A power error on your Samsung washer can be due to several factors. These include issues with the consumer’s power conditions, under or over voltage supply, incorrect plug receptacle usage, or a main PBA fault. To address this, ensure the power supply voltage is correct, check the voltages, ensure the correct plug receptacle is in use, and replace the main PBA if necessary.
What to do if my Samsung WF42H5200AF Washer has a communication error?
If your Samsung washer displays a communication error, it indicates that the signals between the sub and main PBAs are not being sensed. This can be due to incorrect or loose connections. Inspect the connector connections between the sub and main PBAs, look for loose connections, and inspect and repair any faulty soldering on the sub PBA C/Panel.
How to fix a Samsung Washer when the water level sensor is not working?
If the water level sensor in your Samsung washer is not working correctly, it could be due to several reasons: the hose is damaged, clogged, or folded; too much lubricant on the air hose; hose disengagement; a faulty part; a disengaged water level sensor terminal; or a main PBA fault. Check the hose for damage, clear any blockages, straighten the hose, reduce lubricant, ensure proper hose engagement, replace any faulty parts, reconnect the terminal, or replace the main PBA.
Why does my Samsung Washer have an overflow error?
An overflow error in your Samsung washer can occur because water is being supplied continuously due to a failure in water level detection. This can be caused by a clogged drain hose, an injection error, freezing, foreign material in the water supply valve, or a degraded water level sensor. To resolve this, inspect the water level detection system, clear the drain hose, remove any freezing or foreign material, and replace the water level sensor if it is degraded.
What causes a Samsung Washer to display a heater error?
A heater error in your Samsung washer may be caused by a short-circuited or disconnected washing heater, an error in the washing heater within the tub, or issues with the water level sensor leading to overheating. To resolve this, replace or reconnect the washing heater, inspect and resolve any heater or temperature sensor faults, and address any underlying water level sensor issues.
What causes a switch error (main relay error) on my Samsung Washer?
A switch error (main relay error) on your Samsung washer can be triggered by several factors. These include continually pressing the Power button, a jammed or stuck switch, over-tightening the screws holding the sub PBA, continually pressing a button other than the Power button, deformation of an internal plastic injection part or over-tightening a screw for assembling the sub PBA. To resolve this, release the Power button, fix any deformations of the control panel or button, loosen the screws that hold the sub PBA, release other buttons, check and repair the internal plastic parts and loosen the assembly screws.
What causes a temperature sensor error on my Samsung WF42H5200AF Washer?
A temperature sensor error on your Samsung washer can be caused by an error with the washing heater sensor in the tub, an incorrectly connected or disconnected connector, or the water level sensor operating without water. Replace the washing heater sensor, reconnect the temperature sensor connector, and resolve any issues with the water level sensor to address this error.
Provides essential safety guidelines for personnel performing maintenance or repairs.
Details precautions to take before starting any service or repair work.
Outlines necessary safety measures to follow during the servicing process.
Specifies safety checks and procedures to follow after completing service.
Lists common error codes, their causes, and general remarks.
Provides detailed steps and solutions for specific error codes.
General| Style | Front-Loading |
|---|---|
| Color | Inox |
| Washer Capacity | 4.2 cu ft |
| Dryer Capactity | - |
| Max Spin Speed | 1200 RPM |
| Spin Speeds | Medium |
| Spin Class | B |
| Number of Cycles | 9 |
| Cycle Selections | Normal |
| Wash | Shirts |
| Options | Error Diagnostic Display |
| Hours | Smart Control |
| Noise level | - |
| Temperature Selections | Warm |
| Energy Class | - |
| Annual Energy Consumption | 115 kWh |
| Annual Water Consumption | - |
| Water Consumption Per Cycle | - |
| Voltage | 120V |
| Frequency | 60Hz |
| Current | 15 A |
Weight and Dimensions| Depth | 838 mm |
|---|---|
| Height | 984 mm |
| Width | 686 mm |
| Net Weight | 87 kg |
