Why does my Samsung WW70T552DAW1S7 show an unbalance error?
The unbalance error on your Samsung Washer is caused by the laundry load. Check the laundry to resolve this issue, as this occurs by laundry.
Why is there no water supply in my Samsung Washer?
If your Samsung Washer isn't getting water, it could be due to several reasons. Foreign material may be entering the water supply valve, or the water supply valve terminal might not be connected properly. The warm water and rinse connectors could be wrongly connected. Also, check if the PCB terminal from the drain hose to the detergent drawer is not connected, or if the transparent hose is folded or torn. Low water pressure, or a frozen water valve in winter, can also cause this issue. In this case, the water supply valve may be faulty.
Why does my Samsung WW70T552DAW1S7 Washer overflow?
Your Samsung Washer may be overflowing due to a few potential issues. It could be that water is supplied continually because the water level detection isn't working, possibly due to a clogged drain hose or an injection error. Freezing or foreign material in the water supply valve can also cause continuous water supply. A faulty sensor, or a blocked or damaged pressure tube might also be responsible. All these scenarios can be related to a water level sensor fault.
Why is the water level wrong in my Samsung Washer?
If the water level in your Samsung Washer is incorrect, it could be due to several reasons. The hose where the water level sensor is located might be damaged, clogged with foreign material, or folded. Too much lubricant on the air hose insertion part, a hose engagement error, a part fault (like faulty internal soldering), a disengaged water level sensor terminal, or a main PBA fault can also cause this. These issues point to a water level sensor fault.
Why is my Samsung WW70T552DAW1S7 Washer heater not working?
If the heater in your Samsung Washer isn't working, it could be due to a short-circuited washing heater or a disconnected wire. There might be a contact error or temperature sensor fault in the washing heater inside the tub. Also, if the water level sensor operates without water (due to frozen water or another reason) and the temperature sensor detects a high temperature (100 to 150 ?C), the washing machine will turn off the input power. This suggests a heater fault.
What causes communication errors in a Samsung WW70T552DAW1S7 Washer?
Communication errors in your Samsung Washer can occur if the signals between the sub and main PBAs are not sensed. Check the connector connections between the sub and main PBAs carefully and look for any faulty soldering after removing the sub PBA C/Panel. These issues may indicate a Main PCB and Sub PCB Signal Detection fault or a Main PCB and Sub PCB wire connection fault.
Covers general safety guidelines and warnings to follow before commencing product servicing.
Key safety warnings and precautions to observe during and after product maintenance and repair.
Precautionary advice and safety measures to take before and during appliance servicing.
Detailed technical specifications including dimensions, capacity, and power consumption for various models.
Comparison of features and specifications across different washing machine models for selection.
List of optional accessories, their part codes, descriptions, and quantities for installation.
Lists the necessary tools, their types, and remarks for performing disassembly and reassembly procedures.
Illustrations and step-by-step guides for disassembling and reassembling key components.
Explanation of error codes, their causes, and corresponding corrective actions for troubleshooting.
A guide to common washing machine problems, their symptoms, and solutions.
Schematic diagram illustrating the basic wiring connections and components.
Wiring diagram specific to washing machine models featuring an LED display.
Wiring diagram for washing machines equipped with the Q-Drive motor system.
Explanation of the WW6000T project name and the structure of the model code.
Definitions of key terms and components used within the service manual for clarity.
General| Type | Front Load |
|---|---|
| Capacity | 7 kg |
| Energy Efficiency Class | A+++ |
| Spin Speed | 1200 RPM |
| Dimensions (H x W x D) | 850 x 600 x 550 mm |
| Color | White |
| Digital Inverter Technology | Yes |
| Steam Wash | Yes |
| Drum Clean | Yes |
| Quick Wash | Yes |
| Delay End | Yes |
| Water Consumption | 45 L |
| Eco Bubble Technology | Yes |
| Delay Start | Yes |
| Child Lock | Yes |
To Next Page