Sanborn Mfg 200-2357 - User Manual

Questions and Answers

A
Adam BuchananAug 12, 2025
Why does my Sanborn Mfg 200-2357 Air Compressor trip the circuit breaker?
- B
  Brianna McdowellAug 13, 2025
  Excessive current draw can trip the circuit breaker or motor reset switch of your Sanborn Mfg Air Compressor due to several reasons: low voltage or motor overload (ensure adequate power supply and a dedicated circuit, avoiding extension cords if possible, and using dual element time delay fuses if on a fused circuit), a drive belt that's too tight (readjust the belt tension), or restricted air passages (inspect and replace transfer tubes or the check valve if needed).
C
christine57Aug 16, 2025
What to do if my Sanborn Mfg 200-2357 Air Compressor is overheating?
- T
  thompsonbrandonAug 16, 2025
  If your Sanborn Mfg Air Compressor is overheating, it could be due to poor ventilation (relocate the compressor to a cool, dry, well-circulated area, at least 12 inches from the nearest wall), dirty cooling surfaces (clean all cooling surfaces thoroughly), or restricted air passages (replace transfer tubes and/or unloader).
S
Samantha BakerAug 20, 2025
Why is there oil in the discharge air from my Sanborn Mfg Air Compressor?
- M
  Mark DavidAug 20, 2025
  Oil in the discharge air of your Sanborn Mfg Air Compressor can be caused by worn piston rings or cylinder. It may also be caused by a restricted air intake (clean or replace the air filter element(s)), or an oil level that is too high (reduce to the proper level).
F
fitzpatrickjohnAug 23, 2025
What to do if my Sanborn Mfg Air Compressor stalls?
- J
  john22Aug 23, 2025
  If your Sanborn Mfg Air Compressor stalls, the cause might be low voltage to the motor (furnish adequate power), a bad check valve (replace the check valve), or a seized pump. For a seized pump, contact an authorized service center.
T
Tamara LewisAug 27, 2025
How to fix excessive belt wear on Sanborn Mfg 200-2357?
- A
  Ashley AcevedoAug 27, 2025
  Excessive belt wear on your Sanborn Mfg Air Compressor can be caused by a pulley that's out of alignment (realign the pulley with the compressor flywheel), improper belt tension (readjust the tension), or a pulley that wobbles (replace the pulley and check for a damaged crankshaft or flywheel).
J
Jonathan PearsonAug 31, 2025
Why does my Sanborn Mfg 200-2357 have low discharge pressure?
- T
  thomasmillerAug 31, 2025
  Low discharge pressure in your Sanborn Mfg Air Compressor could be due to air leaks (tighten or replace leaking fittings or connections, but do not overtighten), leaking valves, a restricted air intake (clean or replace air filter element(s)), blown gaskets, or worn piston rings or cylinder. For leaking valves, blown gaskets, or worn piston rings/cylinders, contact an authorized service center.
T
Theresa MillerSep 3, 2025
Why is my Sanborn Mfg Air Compressor pump knocking?
- J
  Joy DavisSep 4, 2025
  A knocking sound in your Sanborn Mfg Air Compressor pump may be due to a loose engine pulley or compressor flywheel (retighten the pulley and flywheel, and check the alignment), or a low oil level in the pump crankcase (keep the oil at the proper level at all times). It could also be caused by excess carbon on valves or the top of the piston; in that case, contact an authorized service center.
N
nandersonSep 7, 2025
What to do if Sanborn Mfg 200-2357 Air Compressor won’t start in cold temperatures?
- S
  Stephanie PerezSep 7, 2025
  If your Sanborn Mfg Air Compressor won’t start in cold temperatures, it could be due to too much back pressure in the tank (open the petcock when starting the motor), 40W oil in the crankcase (use synthetic, non-detergent air compressor oil), or the compressor being too cold (move the compressor to a warmer location).