Enter your 4 digit code to reset
the immobilizer, the keypad led
will turn off, the vehicle can now
be driven. If entered incorrectly,
the unit will sound rapid beeps,
the immobilizer will not be reset.
Once the immobilizer has been
reset the vehicle can be driven.
If the ignition is off for 60 sec,
the immobilizer will arm up
automatically.
When the driver’s door is
opened the numbers will light up
to make it easy to see the
numbers at night for easy
operation. The numbers will also
turn on when any button is
pressed. The numbers will turn
off automatically.
2) RESETTING
THE
IMMOBILIZER
To reset the
immobilizer.
Factory default
code 1111
3) DRIVE MODE
Drive mode.
drive
mode
5) NUMBER
LIGHTING
door open
LED
FLASHING
1) IMMOBILIZER
ARMED
Immobilizer
armed mode.
The keypad led will flash a
short flash every 3 seconds.
The vehicle is immobilized.
LED
FLASHING
LED
OFF
1 2
3
4
5
If an incorrect code is entered 4
times, the unit will lock up for
+- 10 minutes. The led will flash
and the unit will
beep.
4) LOCK UP
MODE
Lock up timer.
1 2
3
4
5
lock up mode
LED
FLASHING
RAPIDLY
6) CHANGING YOUR 4 DIGIT CODE
THE UNIT WILL COME DEFAULT FROM THE FACTORY WITH CODE 1 1 1 1
LOADED INTO THE KEYPAD. FOLLOW THE DETAILS BELOW ON HOW
TO CHANGE THE CODE. NOTE : YOU CAN NOT ENTER CHANGE CODE
MODE WHILE IN SERVICE MODE.
RESET THE IMMOBILIZER WITH YOUR 4 DIGIT CODE.
1 2
3
4
5
led flashing
slowly
1 2
3
4
5
IMMOBILIZER ARMED
ENTER EXISTING 4 DIGIT CODE
IMMOBILIZER RESET
HOLD BUTTONS 1 & 5 TOGETHER FOR +/- 2 SECONDS TO ENTER
“OPTIONS MODE”, YOU WILL GET 1 CONFIRMATION BEEP AND THE
LED WILL FLASH RAPIDLY THEN, PRESS AND HOLD BUTTON 5
UNTIL THE KEYPAD SOUNDS A LOUD BEEP AND THE LED TURNS
ON SOLID.
1 2
3
4
5
led on
solid
1 2
3
4
5
PRESS & HOLD BUTTON 1&5
OPTIONS MODE
UNIT IS NOW IN CHANGE CODE MODE
ENTER YOUR NEW 4 DIGIT CODE, AFTER THE CODE IS ENTERED THE
KEYPAD WILL SOUND A LOUD BEEP.
1 2
3
4
5
ENTER THE NEW 4 DIGIT CODE
BEEP
NOW ENTER YOUR NEW 4 DIGIT CODE AGAIN, TO VERIFY THE NEW
CODE. AFTER THE CODE IS ENTERED THE KEYPAD WILL SOUND A
LOUD BEEP, THE KEYPAD LED WILL START TO FLASH. THE 4 DIGIT
CODE HAS NOW BEEN SAVED AND THE UNIT WILL GO INTO ARMED
MODE..
1 2
3
4
5
ENTER THE NEW 4 DIGIT CODE
IF THE FIRST NEW CODE DOES NOT MATCH THE SECOND CODE, THEN
THE KEYPAD WILL SOUND A RAPID BEEP TO WARN YOU THAT THE
CODES DID NOT MATCH. THE NEW CODE WILL NOT BE SAVED, THE
UNIT WILL EXIT CHANGE CODE MODE.
RAPID
BEEPING
1 2
3
4
5
EXIT CHANGE CODE MODE
IF NO NEW CODE IS ENTERED WITHIN 2 MINUTES OR THE
IGNITION IS TURNED ON, THE UNIT WILL AUTOMATICALLY EXIT
CHANGE CODE MODE.
led off
led on
solid
led on
solid
led flashing
slowly
1 2
3
4
5
IMMOBILIZER ARMED
BEEP
BEEP
USER INSTRUCTIONS
button press
Read these instructions for correct system operation. All
points marked are optional features.
*
1 2
3
4
5
PRESS & HOLD BUTTON 5
UNTIL YOU HEAR A LOUD BEEP
led flashing rapidly
BEEP
drive
mode
IMPORTANT NOTE: THE ZX40KPW IS FITTED WITH DEFAULT
CODE 1111 AND IF THIS IS NOT CHANGED BY THE USER TO A NEW
USER CODE THE UNIT WILL SOUND A SERIES OF
LOUD BEEPS EVERY TIME THE IGNITION IS
TURNED ON.
ZX40-KPW
WIRELESS KEYPAD IMMOBILIZER
REV2
This function will only work if connected to a compatible real time
tracking system. Press any button for 3 sec and a panic signal will
be sent to the tracking unit. Panic is disabled in service and Hi-
jack mode.
PANIC MODE
Numbers light
up.
Press any button for 3 sec
r
1 2
3
4
5
TO ENTER SERVICE MODE
ENTER YOUR 4 DIGIT CODE THEN PRESS AND HOLD BUTTON 2 & 4
UNTIL THE KEYPAD SOUNDS A LOUD BEEP AND THE LED TURNS
OFF. THE UNIT HAS NOW EXITED SERVICE MODE.
TO EXIT SERVICE MODE
OPERATION IN SERVICE MODE
THE KEYPAD LED WILL BE ON SOLID, THE IMMOBILIZER WILL NOT
ARM UP DURING SERVICE MODE. THE VEHICLE CAN BE DRIVEN AT
ANY TIME.
AUTO EXIT MODE : IF THE IGNITION IS ON (DRIVE MODE) FOR MORE
THAN 15 MINUTES CONTINUAL DRIVE, THE UNIT WILL
AUTOMATICALLY EXIT SERVICE MODE WHEN THE IGNITION IS
TURNED OFF. IF THE IGNITION IS TURNED OFF BEFORE THE 15
MINUTE TIMER IS UP, THE 15 MINUTE TIMER WILL RESET.
7) SERVICE MODE OPERATION
RESET THE IMMOBILIZER WITH YOUR 4 DIGIT CODE.
THEN, PRESS AND HOLD BUTTON 2 & 4 UNTIL THE KEYPAD
SOUNDS 2 LOUD BEEPS AND THE LED TURNS ON SOLID.
1 2
3
4
5
led on
solid
1 2
3
4
5
UNIT IS NOW IN SERVICE MODE
2 BEEPS
PRESS & HOLD BUTTON 2&4
LED
FLASHING
LED
OFF
led off
1 2
3
4
5
1 2
3
4
5
BEEP
UNIT HAS NOW EXCITED SERVICE MODE
PRESS & HOLD BUTTON 2&4
SANJI SECURITY SYSTEMS (PTY) LTD 106 16TH RD, MIDRAND,
GAUTENG, SOUTH AFRICA. TEL +27 11 266 7500 FAX +27 11 266 7501
E-mail: sales@sanji.co.za http://www.sanji.co.za
QUICK GUIDE
LED FUNCTIONS
Keypad Led quick flash: Immobilizer Armed Mode.
Keypad Led ON: Service Mode.
Keypad Led OFF: Reset / Drive Mode.
Keypad Led Rapid flashing: Program Mode
PROGRAM OPTIONS
* Enter Service Mode: user code 2 & 4
* Exit Service Mode: 2 & 4
* Change Code Mode: user code 1 & 5 then 5
enter code enter code
* Hi-Jack Drivers Door: user code 1 & 5 then 3
* Hi-Jack Drivers Door & Forced: user code 1 & 5 then 3
* Hi-Jack Cancel: user code 1 & 5 then 3
* Learn Master Code: user code 1 & 5 then 1
enter six digit enter six digit
* Use Master Code: 3 & 5 enter six digit code
To Next Page
Need help?
General
