Sanji ZX70MK2 - User Manual

SANJI Security Systems (Pty) Ltd
68 Kyalami Boulevard, Kyalami
Business Park Midrand 1684,
Gauteng, South Africa
TEL +27 11 875 0000
FAX +27 11 466 0286
E-mail: sales@sanji.co.za
http://www.sanji.co.za
ZXMK2-USER-REV1
FITMENT CENTRE STAMP:
28) ONE EVENT
OVERRIDE
To override
the
immobiliser
or alarm, in
the event of
a flat remote
battery.
In any mode, t
and press the hidden push button
for +/- 2 seconds until the unit
chirps once, the system will be
reset. This is a once off
override.
urn the Ignition on
ZX300Mk2 ONLY
29) BOOT
RELEASE
FUNCTION
To open the
boot.
Press the boot release button
(ignition off). The boot will open.
If the alarm was set the boot will
open and the alarm will be reset.
REQUIRES A 3 BUTTON REMOTE
26) USING YOUR PINCODE OVERRIDE (ZX400Mk2 ONLY)
The ZX400Mk2 can be temporarily overridden by entering the supplied 5
digit pincode override by means of turning the ignition switch on and off
in a sequence as per instructions below. If the unit is in immobiliser armed
mode (dash led solid) you can begin to enter your code. If the alarm is set,
open the door and
turn the ignition on. Wait for the unit to stop sounding,
turn the ignition off. You can begin to enter your code.
Digit 1 [number 3]
Turn ignition key on, led will start to flash, on the
THIRD flash, turn
ignition key off, the indicators will flash once, you have now successfully
put your first digit in.
Digit 2 [number 1]
Turn ignition key on, led will start to flash, after the
FIRST flash, turn
ignition key off, the indicators will flash once, you have now successfully
put your second digit in.
Digit 3 [number 4]
Turn ignition key on, led will start to flash, after the
FOURTH flash, turn
ignition key off, the indicators will flash once, you have now successfully
put your third digit in.
Digit 4 [number 2]
Turn ignition key on, led will start to flash, after the
SECOND flash, turn
ignition key off, the indicators will flash once, you have now successfully
put your fourth digit in.
Digit 5 [number 1]
Turn ignition key on, led will start to flash, after the
FIRST flash, turn
ignition key off, the indicators will flash once, you have now successfully
put your fifth digit in and have successful overridden your vehicle.
If you enter an incorrect digit the unit will not flash the indicators and will
revert back to the first digit. If you enter an incorrect digit 3 times the
unit will sound the alarm. Turn the ignition on and wait for the unit to
stop sounding. You can now re-enter your code.
27) AUTO RE-ARM (safety against code jammers)
The unit will Auto re-arm after 30 seconds if the user has unlocked the
vehicle via the remote and not pressed the set button on again. The alarm
will only Auto re-arm and lock the doors if no doors or ignition has been
pulsed.
*
ISO 9001:2008
quality company
TA-2013/037
SanjiMXMk2InstructionManual.indd 1 2013/08/15 2:37 PM

Summary

USING YOUR PINCODE OVERRIDE

Digit I

Enter first pincode digit by specific ignition sequence and indicator flashes.

Digit 2

Enter second pincode digit by specific ignition sequence and indicator flashes.

Digit 3

Enter third pincode digit by specific ignition sequence and indicator flashes.

Digit 4

Enter fourth pincode digit by specific ignition sequence and indicator flashes.

Digit 5

Enter fifth pincode digit to successfully override the vehicle's system.

AUTO RE-ARM

ONE EVENT OVERRIDE

BOOT RELEASE FUNCTION

Sanji ZX70MK2 Specifications

General

Brand	Sanji
Model	ZX70MK2
Category	Car Alarm
Language	English