Sanyo C7 - Page 12

Automatic stop
This
unit
employs
full
release
automatic
stop
at
the
end
of
the
tape.
CASSETTE DECK OPERATION
Press
the
STOP
button
before
turning
the
power
off
when
the
unit
is
in
the
recording
or
playback
mode
otherwise,
the
pinch
roller
will
be
damaged
and
cause
inconsistent
tape
speed,
Recording
a) Recording from a microphone
*
Make
sure
that
the
VOLume
conirol
is
set
to
the
minimum
position
to
prevent
feedback.
*
Set
the
MIC
MIX
VOLume
control
to
the
maximum
position.
Set the POWER switch to the ‘‘on”’ position.
Press the ““TAPE” function selector.
Press the EJECT button and insert a cassette.
Set
the
tape
select
switch
for
the
type
of
tape
being
used.
Set the DOLBY NR switch to “on” or “‘off’’ as desired.
Press the PAUSE button. The pause indicator will light up.
Press
the
RECORD
button.
The
record
and
play
indicators
will
light
up.
Reset the counter to ‘000’.
Adjust
the
left
and
right
channel
recording
levels
with
the
INPUT
LEVEL
controls
so
that
the
VU/
SOUND meters illuminate within “0 dB” (Fig. 16).
10.
Re-press
the
PAUSE
button
to
start
recording.
The
pause
indicator
will
go
off.
11.
Since
you
can
monitor
through
the
speakers
regardless
of
the
recording
level,
adjust
the
VOLume,
BASS,
TREble
and
BALance
controls
to
the
desired
sound
level
and
tone
quality.
12.
Press
the
STOP
button
to
stop
recording
at
any
time.
13.
When
the
end
of
the
tape
has
been
reached,
the
automatic
stop
will
be
activated.
NOTE:
*
To
prevent
feedback,
the
monitor
sound
should
be
reduced
as
much
as
possible.
*
If
you
require
to
monitor
with
headphones,
connect
them
to
the
PHONES
socket.
* This unit cannot be possible stereo live recording.
OMONAAPP WN
b) Recording from the tuner or a turntable
*
Make
sure
that
the
MIC
MIX
VOLume
control
is
set
to
the
minimum
position.
Tune
in
a
desired
radio
programme
as
described
in
“TUNER
OPERATION”
or
play
a
record
as
described
in
“TURNTABLE
OPERATION”
under
“TUNER/AMPLIFIER
SECTION”
and
follow
steps
“3”
ta
"13"
of
“Recording
from
a microphone”
section.
o)
Mixing
recording
with
a
radio
programme
and
a
microphone
or
a
turntable
and
a
microphone
Make
sure
that
the
MIC
MIX
VOLume
control
is
set
to
the
minimum
position.
1.
Tune
in
a
desired
radio
programme
as
described
in
“TUNER
OPERATION”
or
play
a
record
as
described
in
“TURNTABLE
OPERATION”
under
“TUNER/AMPLIFIER
SECTION”.
2.
Follow
steps
3”
to
“9”
of
‘Recording
from
a
microphone”
section.
3.
Adjust
the
microphone
recording
level
with
the
MIC
MIX
VOLume
control
so
that
the
VU/SOUND
meters
illuminate
with
in
0
dB”.
4.
Follow
steps
“10”
to
13”
of
‘Recording
from
a
microphone”
section.
Reyoeck
Make
sure
that
the
MIC
MIX
VOLume
control
is
set
to
the
minimum
position.
1. Set the POWER switch to the “on” position.
2. Press the “TAPE” function selector. :
3. Press the EJECT button and insert the recorded cassette.
4. Set the tape select switch for the type of tape being used.
5.
Set
the
DOLBY
NR
switch
to
“‘on”
or
“off”,
according
to
whether
the
tape
has
been
recorded
with
the
Dolby NR System or not.
. Press the PLAY button. The play indicator will light up.
.
Adjust
the
VOLume,
BASS,
TREble
and
BALance
controls
to
the
desired
sound
level
and
tone
quality.
~ oO.