Sanyo DC D30 - CD PLAYER;TUNER;TIMER CONTROLS; Unit Controls Overview; REMOTE CONTROL; Remote Control Functions

LASER BEAM SAFETY PRECAUTIONS (CD)
Do not look straight at the laser beam from the pickup and do
not point the beam at your fingers or any other part of your
body.
Note: The laser beam must never be allowed to enter the eyes
since this may damage the eyes.
Power must never be supplied to a pickup with a damaged laser
output part (objective lens, etc.).
INVISIBLE
OUTPUT POWER
0.6 mW
LASER RADIATION EXPOSURE TO BEAM -
Structural Safety Interlock
This model has a disc chuck lever and top lid. This disc chuck
lever and top lid prevent to expose the laser beam for users.
IS DANGEROUS CLASS 1
MAX WAVELENGTH 790 nm
LASER PRODUCT
CLASS 1 LABER
CAUTION — INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
AOVARSEL — USYWLIG LASER STRALING VEO AGNING, NAR
SIKKERHEOSAFBRYDERE ER UDE AF FUNKTION, UNDGA UDS ATTELSE
FOR STRALING.
VARWING — OSYNLIG LASER STRALNING WAR DENNA DEL AR OPPNAD
OCH SPARR AR URKOPPLAD. STRALEN AR FARLIG.
VORSICHT — UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN
DECKEL GEGFFNET UND WENN SICHERHEITSVERRIEGELUNG
UBERBRUCKT IST. NICHT, OEM STRAHL AUSSETZEN.
| VARO — AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NAKYMATTOMALLE LASERSATEILYLLE. ALA KATSO SATEESEEN.
1. Precautions for handling the pickup and semiconductors
(particularly the ICs)
a. The pickup and semiconductors (particularly the ICs) may be
damaged if they come into contact with a source of high
voltage static electricity. Do not bring them, therefore, into
contact with or into the vicinity of anything which has been
charged with high voltage static.
b. The pickup consists of a large number of optical and precision
parts. Do not store or repair it, therefore, in any location
with a high temperature, high humidity, high magnetic fields
or high dust concentration. (Since the pickup contains a
powerful magnet, it must not be brought near any
magnetized objects.)
c.Do not apply strong external pressure to the pickup or subject
it to impact. Actions like these can cause the printed circuit
board to crack or malfunctioning to occur.
d. The pickup is a single integrated part which has been very
precisely adjusted. Therefore, its adjustment points and set
screws must not be touched.
2. How to prevent static during handling
a. When replacing any of the parts, disconnect the power plug
from the unit being repaired.
b. All measuring instruments, tools and repair equipment must
be grounded. Cover the work bench where the repair work
will be done with a grounded electrically conductive sheet.
c.Ground the metal part of the soldering iron in order to
safeguard against leakage of electricity from the heater.
CAUTION - USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
ACHTUNG - WENN ANDERE ALS DIE HIER SPEZIFIZIERTEN BEDIENUNGS- ODER JUSTIEREIN-
RICHTUNGEN BENOTZT ODER ANDERE VERFAHRENS-WEISEN AUSGEFUHAT WERDEN, KANN DIES ZU
GEFAHRLICHER STRAHLUNGSEXPOSITION FOHREN.
ATTENTION - L’EMPLOI D’'ORGANES DE COMMANDE OU DE REGLAGE, OU L'EXECUTION DE
PROCEDURES, AUTRES QUE CEUX SPECIFIES DANS LE MODE D’EMPLOI, PEUT PROVOQUER UNE
EXPOSITION DANGEREUSE AU RAYONNEMENT.
OPGELET - HET GEBRUIK VAN REGELAARS OF HET MAKEN VAN AFSTELLINGEN E.D. DIE NIET IN DEZE
GEBSRUIKSAANWIJZING ZIJN BESCHREVEN KAN LEIDEN TOT SCHADELIJKE STRALINGEN,
VARNING! OM APPARATEN ANVANDS PA ANNAT SATT AN VAD SOM BESKEIV 1 DENNA BRUKSAN-
VISNING, KAN ANVANDAREN UTSATTAS FOR OSYNLIG LASERSTRALNING, SOM OVERSKRIDER
GRANSEN FOR LASERKLASS 1.
CAUTELA - L'USO DI COMANDI, AGGIUSTAMENTI O PROCEDIMENTI DIVERSO DA QUELLO QUI SPECIFI-
CATO PUO DAR LUOGO AD ESPOSIZIONE A RADIAZIONI PERICOLOSE.
VAROITUS! LAITTEEN KAYTTAMINEN MUULLA KUIN TASSA KAYTTOOHJEESSA MAINITULLA TAVALLA
SAATTAA ALTISTAA KAYTTAJAN TURVALLISUUSLUOKAN 1 YLITTAVALLE NAKYMATTOMALLE
LASERSATEILYLLE.
d. Repair personnel must wear grounding bands around their
wrists to discharge static picked up by their bodies. These
bands are grounded through a resistor (with a 1Mlt
resistance).
Note: Under no circumstances must be the grounding bands be
grounded without a resistor (with a 1MIF resistance) since
doing so involves the risk of electric shocks.
Since static in the clothes of the repair personnel will not be
discharged by wearing grounding bands, every care must be
taken not to allow the clothes to touch the pickup and
semiconductors (particularly the ICs).
e. The pickup, which is a single integrated part, is kept in a
conductive bag. Use this bag to convey the pickup from one
place to another. in order to avoid damage resulting from
static which may occur when the pickup is removed from the
bag, make sure that it is not placed on top of the bag.
3. Cleaning the lens surface
a. Blow off dust on the lens using the kind of air brush which is
used for cameras.
b. Remove stubborn dirt with a cotton swab dipped in isopropyl
alcohol. Do not use any other type of cleaning fluid since it
may mark the plastic lens.
Notes: @®Do not use too much isopropyl alcohol: the excess may
seep inside the pickup.
@The lens is held in place by a very feeble support
spring. Therefore, when cleaning the lens, avoid
applying any more force by the cotton swab than is
necessary since this may bend the support spring out of
shape.