Sanyo XT-43S8100FS - Network Connection Methods; System Settings Menu Overview

Using your TV
17
Select MENU > Network, then the Network menu
appears on the right with the following options. Press
Ź to enter and use Ÿź to choose an option.
Internet connection:
1. Select Internet connection and press OK to enter.
2. 3UHVVŸź
to select On and press OK
Interface:
1. Select Interface and press OK to enter.
2. Press Ÿź to select Ethernet or Wireless and
press OK
• Ethernet
IP settings:
Select IP settings and press OK to enter. You can
set Address type to Auto or Manual.
• Select Auto if you want the TV to acquire and
enter the needed IP address automatically.
• Select Manunal if you want to enter your IP
address manually, then:
-
- Enter the IP address. Subnet mask, Default
gateway, Primary DNS and Secondary DNS
values. Use the numeric buttons to enter
numbers and the Ÿź
/ buttons to move
• Once IP setting is completed, press Ÿź to
select OK and press OK to confirm. The set
will try to connect to the network and inform
you about the result. Press
to return to the
Network menu.
• Wireless
Wireless settings:
Select
MENU > Network, then select Wireless
settings to connect to a wireless network. You can
set the wireless network connection in 3 ways:
1. Scan: Select Wireless settings > Scan, then
press OK, the TV will scan all access points
within range. The access points found by the
TV will be displayed. Select an available access
point, then press OK to connect the TV to it.
Notes:
If you select a protected access point, you will
have to enter the corresponding password.
Press OK on the remote control to display
virtual keyboard to enable you to enter it.
This set has a memory function of available
access points, which enables your set to be
connected to the network even if you switch on
TV after power off.
2. Manual:
Select Wireless settings > Manual,
then press
OK
, you will be prompted to enter the
correct SSID of an available wireless router to set
up the
connection.
3. Au t o :
If your AP(Ac c e s s P o i n t ) s u p p o r t s
WPS(WiFi Protected Setup), you can connect
to the network via PIN(Personal Identification
Number) or PBC(Push Button Configuration).
WPS will automatically configure the SSID and
WPA key in either mode.
Select Wireless settings > Auto and press
OK
to enter.
• PIN: Select PIN and press OK to enter. Choose
a random PIN code. Make sure this code is
installed on the AP. (For the procedures, refer
to your router manual.) Select OK and press
OK to set up the connection.
• PBC: If your router has a PBC push button,
select PBC and press OK to enter. Press
the PBC push button on your router within 2
minutes before you select OK and press OK
again. Your TV will automatically acquire all the
network setting values it needs and connect to
your network.
Information:
Select Information and press OK to enter. You will
check the information on current connection, such
as Interface, Address type, IP address, etc., press
Ÿź to select Information and press OK to enter.
Press
to return to the Network menu.
Connection test:
Select Connection test and press OK to enter. You
will check the Internet connectivity.
System
Select MENU > System , then the System menu
appears on the right with the following options. Press
ŹWRHQWHUDQGXVHŸźWRFKRRVHDQRSWLRQ
Timer: The Timer menu allows you to set the time
zone on your TV set, to program an automatic turn-off
or wake-up timer .
Select System > Timer and press OK
Timer options are as below:
• Time zone: Use Ÿź
to select the local time
zone.
• Clock: Press OK to display its options:
• Synchronization: Use Ÿź to select on or off
Manual. If on is selected, the TV will get the time
automatically cannot be adjusted. If you select
Picture
Sound
Channel
Smart TV
Network
System
Support
Input settings
Location
Auto source
Sports mode
LED Indicator
Instant power on
Reset
Timer
Lock
...
...
...
...
Home
On
Off
Normal
Off