Schaudt Electroblock EBL 271 - Closing Down the System; System Shutdown Procedure

Instruction Manual for Electroblock EBL 271
7
Date: 14.02.2011
811.523 BA / EN
Fault RemedyPossible cause
12V supply does not work
i
n
t
h
e
l
i
v
i
n
g
a
r
e
a
12V main switch for the li-
v
i
n
g
a
r
e
a
b
a
t
t
e
r
y
i
s
s
w
i
t
12V main switch for the li-
v
i
n
g
a
r
e
a
b
a
t
t
e
r
y
m
u
s
t
b
e
i
nt
h
e
l
i
v
i
ng area v
i
ng area
b
attery
i
ssw
i
t-
ched off
v
i
ng area
b
attery must
b
e
switched on
Not all plugs or fuses are
p
l
u
g
g
e
d
i
n
t
o
t
h
e
e
l
e
c
t
r
o
Insert all plugs and fuses
(
c
o
r
r
e
c
t
v
a
l
u
e
s
)
i
n
t
o
t
h
e
p
l
ugge
d
i
nto t
h
ee
l
ectro-
block
(
correct va
l
ues
)
i
nto t
h
e
electroblock
D
e
f
e
c
t
i
v
e
f
u
s
e
o
r
w
i
r
i
n
g
C
h
e
c
k
f
u
s
e
a
n
d
w
i
r
i
n
g
D
e
f
ect
i
ve
f
use or w
i
r
i
ng
C
h
ec
k
f
use an
d
w
i
r
i
ng
Defective electroblock Contact customer service
Marker lights do not work Polyswitch fuse has trip-
ped
Switch off the electroblock
for at least 1 minute (di-
s
c
o
n
n
e
c
t
f
r
o
m
2
3
0
V
s
u
p
sconnect
f
rom
2
3
0
V
sup-
ply if required), then switch
it on again
No control signal from the
basic vehicle
Check the base vehicle
Y The charging current is reduced automatically if the device becomes too
hot due to excessive ambient temperature or lack of ventilation. Always
prevent the device from overheating nevertheless.
Y If the automatic shutdown mechanism of the battery monitor is triggered,
fully charge the living area battery.
3.4 Closing down th e system
A battery is isolated by switching off the main switch on the IT .../LT ... con-
trol and switch panel and by disconnecting a plug connector .
Y ATTENTION!
Damage to the living area battery as a result of total discharge. So therefore:
F Fully charge the living area battery before and after closing down the
system. (Connect vehicle to the mains with an 80Ah battery at least
12 hours and with a 160Ah battery at least 24 hours).
When the motorhome is not used for a long time, consumers with a perma-
nent supply should be disconnected from the battery.
" 12V supply on the IT ... / LT control and switch panel must be switched
off.
" Fully charge t he living area battery before closing down the system.
" Remove the MNL connector on block 4 of the electroblock.
The living area battery now only supplies the permanent positive input of the
radio (e.g. to prevent the code from having to be re-entered every time after
closing down).
Follow the instructions of the battery manufacturer.
Closing down