This document is an installation, operation, and care manual for Scientific Laboratory Equipment's Steam Bath models 401 and 402.
Function Description
The Scientific Steam Bath is a laboratory instrument designed for continuous operation, providing a controlled heating environment through steam. It is primarily used to heat samples or solutions in a laboratory setting. The unit features a tank assembly where water is heated to produce steam, and a tray with multiple stations (6 for Model 401, 12 for Model 402) to accommodate various containers. The automatic water level control device ensures consistent operation, while a manual reset safety thermostat protects the heating element from running dry.
Important Technical Specifications
Model 401 (6 Station Steam Bath):
- Power: 2000 Watts
- Voltage/Frequency: 230V/50Hz
- Dimensions (approximate):
- A (Length): 410 mm
- B (Width): 110 mm
- C (Height): 280 mm
Model 402 (12 Station Steam Bath):
- Power: 2000 Watts
- Voltage/Frequency: 230V/50Hz
- Dimensions (approximate):
- A (Length): 530 mm
- B (Width): 110 mm
- C (Height): 405 mm
Common Components (Models 401 & 402):
- Heating Element: 2000W 230V
- Thermostat: Control thermostat (Part No. 1-THERM-URB0012)
- Pilot Light: (Part No. 1-PL-GP)
- Rings: Includes Ring Knob, Centre Ring, 65mm Ring, 85mm Ring, and 105mm Ring for accommodating different vessel sizes.
- Controls: Steambath Inlet Control, Steambath Level Control.
- Safety Features: Manual reset safety thermostat, Safety Cap, Pilot Light.
- Power Cord: Standard power cord with cable grip.
Electrical Connection Information:
- The unit operates on alternating current (A.C.) only. DO NOT CONNECT TO DIRECT CURRENT (D.C.).
- It requires an individual 15A mains outlet. DO NOT OVERLOAD THE CIRCUIT.
- The incoming voltage must match the rated voltage found on the serial plate (230V/50Hz).
Usage Features
Installation:
- Install the unit in a convenient location for ease of cleaning, maintenance, and general operation.
- Ensure the surface where the unit is placed is level.
- If positioned near a wall or partition, ensure these are made of non-combustible heat insulating material, adhering to fire prevention regulations.
- The unit is equipped with an automatic water level control device for ease of use.
- The manual reset safety thermostat provides protection for the element if the bath runs dry.
Operation:
- The unit is designed for continuous operation.
- It is intended for use by properly trained laboratory staff.
- Always use earthed outlets matching the serial plate voltage.
- Equipment should be installed by qualified personnel in accordance with local codes and ordinances.
- Do not operate the equipment if it is damaged or malfunctioning.
Safety Precautions:
- Burn Hazard: Hot surfaces and liquids can cause burns. Allow surfaces to cool before handling.
- Electric Shock Hazard: Prevent water and other liquids from entering the equipment's interior. Do not spray water or cleaning products directly onto the unit.
- Do not use the equipment if the power cord is damaged or modified.
- Ensure the equipment and power supply cord do not come into contact with hot surfaces.
- The control compartment contains dangerous voltages; maintenance and servicing requiring panel removal should only be performed by qualified service personnel.
Maintenance Features
Cleaning:
- Before cleaning, disconnect the power plug from the mains socket.
- Clean the unit using a damp cloth with soapy water.
- Do not submerge the unit in water or subject it to water spray.
- Periodic maintenance is generally not required for the steam bath's continuous operation.
- For stainless steel parts: Clean with water and soap. Avoid abrasive detergents. Rinse well and dry carefully. Do not use products containing aggressive chemicals, acids, or chlorine (even diluted) on stainless steel.
Warranty:
- All Scientific equipment comes with a standard ONE-year warranty.
- A 1-Year Extended Warranty is available for customers who register their warranty online at www.scientific.co.za within the first year of purchase, extending the total warranty period to two years.
- The manufacturer guarantees the unit is free from defects in materials and workmanship for one year from the original installation date.
- Liability under warranty is limited to repairing the defective unit or part, provided it is sent carriage paid to an authorized dealer.
- The warranty is void if damage occurs due to accident, carelessness, improper installation, lack of proper set-up/supervision, or operation contrary to instructions. Repairs in such cases will be made at a reasonable cost.
- Work performed by unauthorized personnel or service agencies voids the warranty.
- All Scientific equipment comes with a two-year warranty on components and defective workmanship (Terms & Conditions apply).
To Next Page
Need help?
General
