Why is my Sea Breeze Air Conditioner indoor unit making noise?
The indoor unit of your Sea Breeze Air Conditioner may emit noise when defrosting starts or stops; this is due to the refrigerant flow reversing directions. Normal refrigerant flowing in the unit can also cause some noise.
What to do if my Sea Breeze SHE12H4ZIGB Air Conditioner remote is not working?
If the wireless remote control for your Sea Breeze Air Conditioner isn't working, try resetting the unit by disconnecting the main power for 30 seconds, then reconnecting it. Ensure you're within receiving range and that there are no obstructions. Replace the batteries. If the remote is still not working, it may be damaged.
What to do if my Sea Breeze SHE12H4ZIGB remote control is not working?
If the wireless remote control for your Sea Breeze Air Conditioner isn't working, try these steps: First, reset the unit by disconnecting the main power for 30 seconds and then reconnecting it. Ensure you are within receiving range and that there are no obstructions. Replace the batteries. If it still fails, the remote control might be damaged.
How to fix a Sea Breeze Air Conditioner remote that's not working?
If the wireless remote control for your Sea Breeze Air Conditioner isn't working, try these steps: Reset the unit by disconnecting the main power for 30 seconds, then reapply. Ensure the remote is within receiving range and not obstructed. Replace the batteries. Check for any damage to the remote control.
Why is my Sea Breeze Heat Pump cooling or heating efficiency is not good?
If your Sea Breeze Heat Pump isn't cooling or heating well, make sure the temperature setting is correct. Check that the air inlet or outlet vents aren't blocked, and ensure the filter is clean. Also, verify that windows and doors are closed, the fan isn't set to low speed, and there isn't a heat source in the room.
Why is my Sea Breeze Air Conditioner making noise inside?
The noises from the indoor unit of your Sea Breeze Air Conditioner could be due to the refrigerant flow reversing directions when defrosting starts or stops, which is normal. It could also be due to normal refrigerant flowing in the unit.
What to do if my Sea Breeze SHE12H4ZIGB Air Conditioner is leaking water inside?
If water is leaking into the room from your Sea Breeze Air Conditioner, it could be due to excessively high air humidity. Ensure all windows and doors are closed. If the issue persists, it may require professional assistance from a service technician.
Why is my Sea Breeze SHE12H4ZIGB leaking water outside?
Water leakage in the outdoor unit of your Sea Breeze Air Conditioner is normal in two scenarios: when the unit is running in Auto Defrosting mode (ice will thaw and drip into the pan) and when the unit is running in HEAT mode (water adhered to the condenser coil drains into the pan).
Why is there water leaking from the outdoor unit of my Sea Breeze Air Conditioner?
Water leakage from the outdoor unit of your Sea Breeze Air Conditioner is normal in certain situations: When the unit is running in Auto Defrosting mode, ice will thaw and drip into the pan. Also, when the unit is running in HEAT mode, water adhered to the condenser coil drains into the pan.
What to do if my Sea Breeze SHE12H4ZIGB Air Conditioner is not running?
If your Sea Breeze Air Conditioner isn't running, check the following: * Is the power on? * Has the circuit protection device tripped? * Is the voltage within the correct range (this should be tested by a professional)? * Is the timer on? Also, be aware that a 3-minute delay occurs before each compressor start.
Lists the key features and capabilities of the multi-zone system.
Instructions on how to operate the unit using the emergency switch.
Details the function of each button on the remote control keypad.
Explains how to use different operating modes like AUTO, COOL, HEAT, DRY, FAN, SLEEP.
Procedure for cleaning the air filters, including recommended frequency.
Common issues and checks when the air conditioner fails to start.
Diagnosis for poor cooling or heating performance and potential causes.
This document describes the Sea Breeze High Efficiency Series Indoor Wall Mounted Unit Heat Pump Models, including SHE9H4ZIGB, SHE12H4ZIGB, SHE18H4ZIGB, and SHE24H4ZIGB. These units are designed for multi-zone mini-split applications, offering both cooling and heating functionalities.
The Sea Breeze High Efficiency Series units are indoor wall-mounted heat pumps designed to provide comfortable indoor temperatures through various operating modes. They utilize variable speed inverter type compressors for increased efficiency and quiet operation. The units can function in AUTO, COOL, DRY, FAN, and HEAT modes. In AUTO mode, the unit automatically switches between COOL, HEAT, or FAN to maintain a temperature range of 68 °F to 77 °F. COOL mode cools the room to a set point between 61 °F and 86 °F, with the indoor fan continuously running to maintain consistent room temperature. HEAT mode (for heat pump units only) heats the room to a set point between 61 °F and 86 °F, and the indoor fan will turn off once the set point is satisfied. DRY mode cools at 90% capacity with the fan running at LOW speed to dehumidify. FAN mode allows for fan-only operation with adjustable speeds (AUTO, HIGH, MEDIUM, LOW). The units also feature a SLEEP mode for quiet, energy-saving operation, a TURBO mode for maximum air flow in HEAT and COOL modes, and a PURGE/BLOW function to dry the evaporation coil and prevent mold and mildew. Individual temperature selection is available for each zone in multi-zone setups.
The units are rated for 16 SEER efficiency.
The units are controlled primarily by a wireless remote control, which features an LCD display showing current settings and operational status. Keypad functions on the remote include ON/OFF, MODE selection (AUTO, COOL, DRY, FAN, HEAT), temperature adjustment (+/-), FAN speed control (AUTO, HIGH, MEDIUM, LOW), SWING for louver movement, CLOCK setting, TIMER ON/OFF, PURGE/BLOW, TURBO, SLEEP, DISPLAY (to turn wall unit display on/off), FOLLOW ME (transfers room temperature sensing to the remote), and LOCK KEYPAD. An auxiliary button on the indoor unit allows for emergency operation if the remote is misplaced, starting the unit in default AUTO mode. The units support manual adjustment of horizontal louvers for air flow direction. Multi-zone systems allow for individual temperature selection per zone, but all indoor units must operate in the same mode (either all cooling or all heating) to avoid an E7 error code. The remote control also allows selection between °F and °C temperature display.
Routine care and maintenance are crucial for optimal performance.
General| Compressor Type | Rotary |
|---|---|
| Type | Split |
| Cooling Capacity (approx) | 12000 BTU/h |
| Power Supply | 220-240V, 50Hz |
| Operating Temperature | 16°C |
To Next Page
