Why Sea-doo Boat engine does not turn over?
The Sea-doo Boat engine might not turn over because the safety lanyard is removed, a fuse is burnt, the battery is discharged, connections are corroded or loose, the engine is water-flooded, there's a faulty sensor or MPEM, the engine is seized, or the jet pump is seized. Install the cap over the post. Check the wiring and replace the fuse(s).
What to do if Sea-doo Boat can not reach top speed?
If your Sea-doo Boat can't reach top speed, it could be due to a clogged jet pump water intake, a damaged impeller, a safety lanyard that limits speed, or the monitoring system putting the watercraft in limp home mode. Clean the jet pump water intake and check for damage. Replace a damaged impeller. Use a safety lanyard that allows reaching the top speed. Release the throttle so that the engine returns to idle speed.
What to do if Sea-doo Boat engine turns normally?
If the Sea-doo Boat engine turns normally but doesn't start, the fuel tank valve might be closed, the fuel tank could be empty or water-contaminated, the fuel filter might be clogged, the spark plugs could be fouled, the choke might be misused, the engine could be fuel-flooded, there could be a faulty component in the fuel injection system, a burnt fuel pump fuse, or an electrical problem. Turn the fuel tank valve to the ON position. Refill the fuel tank, siphoning out any old fuel and replacing it with fresh fuel. Clean the fuel filter and check the tank for water. Replace the spark plugs.
What to do if Sea-doo Boat engine turns slowly?
If the Sea-doo Boat engine turns slowly, it might be due to loose battery cable connections, a discharged or weak battery, or a worn starter. Check, clean, and tighten the battery cable connections.
Why Sea-doo Boat monitoring beeper sounds continuously?
The Sea-doo Boat monitoring beeper may sound continuously due to a clogged jet pump water intake or a clogged coolant system. Clean the jet pump water intake. Flush the cooling system.
What to do if Sea-doo Boat has lean fuel mixture?
If your Sea-doo Boat has a lean fuel mixture, it could be due to low, stale, or water-contaminated fuel; a clogged fuel filter; a partially open fuel tank valve; or clogged injectors. Siphon and/or refill the fuel tank. Turn the fuel tank valve to the ON position.
What to do if Sea-doo Boat engine lacks acceleration or power?
If your Sea-doo Boat engine lacks acceleration or power, this could be due to weak spark or water in the fuel or injection oil. Siphon and replace the fuel or injection oil.
What to do if Sea-doo Boat has rich fuel mixture (high fuel consumption)?
If your Sea-doo Boat has a rich fuel mixture, it might be due to a dirty or clogged flame arrester or a partially closed choke. Clean or replace the flame arrester.
Why Sea-doo Boat engine cannot run above idle speed?
The Sea-doo Boat engine may not run above idle speed because the monitoring system put the watercraft in limp home mode due to a component malfunction. Try removing and reinstalling the safety lanyard on its post.
What causes abnormal noise from Sea-doo Boat propulsion system?
Abnormal noise from the Sea-doo Boat propulsion system can be caused by weeds or debris jammed around the impeller, or a damaged impeller shaft or drive shaft. Clean and check for damage.
General| Manufacturer | Sea-Doo |
|---|---|
| Model | RX DI |
| Category | Personal Watercraft |
| Displacement | 951 cc |
| Horsepower | 130 hp |
| Fuel System | Direct Injection |
| Dry Weight | 650 lbs |
| Seating Capacity | 2 |
| Fuel Capacity | 15.9 gallons |
Basic rules for safe boating, operation, and protective gear.
Identifying labels and locating controls for different watercraft models.
Function of safety lanyard, DESS, handlebar, throttle, start/stop, VTS, gauges, and info center.
Safe fueling, recommended types, lubrication, and break-in process.
Pre-operation checks, operating instructions, post-operation care, and special procedures.
Inspection chart, lubrication, cable, and carburetor adjustments.
Precautions for towing, storing, and preparing the watercraft for use.
Diagnosing issues via beeper codes, engine, and performance problems.
Detailed engine, electrical, propulsion, dimensions, and capacities specs.
Conversion factors, glossary of abbreviations, and owner address update form.
To Next Page
