Sealey HVD30 - INTRODUCTION AND SPECIFICATION; OPERATION; FAN OPERATION; MAINTENANCE

3. SPECIFICATION
Model No:............................................................. HVD30.V3
Current: ........................................................................ 0.52 A
Fan diameter: ................................................. Ø760 mm (30”)
Speed range: .....................................................800-900rpm
Speeds: ................................................................................ 2
Supply: .......................................................................... 230 V
Maximumfanowrate(F): ........ 283.4 m
3
/min (10008.2 cfm)
Fan power input (P): ................................................. 118.6 W
Servicevalue(SV): .........................................2.4 (m
3
/min)/W
Standby power consumption (P
SB
): ..................................0 W
Seasonal electricity consumption (Q): ................. 38.0 kWh/a
Fan sound power level (L
WA
): ....................................78 dB(A)
Maximum air velocity (c): ........................................... 2.2 m/s
4. OPERATION
 WARNING!Ensurethatyouread,understandandapplysafetyinstructionsinSection1beforeusingfan.
4.1. Check that the speed control is set to “0” (off) and then plug into the mains power supply and switch the power on.
4.2. The fans feature 2 speeds which are selectable using the switch located at the back of the fan, above the motor.
4.3. Adjust the direction of the air flow by moving from side to side and tilting the fan up or down as required.
4.4. When you have finished using the fan ensure you turn the speed control switch to “0” (off) and disconnect the fan from the mains
power.
5. MAINTENANCE
 WARNING! Ensure that the fan is disconnected from the mains power supply before attempting any of the following:
5.1. Use a soft, damp cloth to clean the fan.
8 DO NOT immerse the fan in water and never allow water to drip onto the motor housing. DO NOT use solvents, petroleum, paint
thinner or other chemicals to clean the fan.
5.2. To clean the fan blade, undo the cross headed screws around the circumference, remove the grille and clean the blade with a
slightly damp cloth. Replace the grille as required and refit the cross headed screws.
5.3. Shouldthemotor,switchorthepowerleadrequireserviceormaintenancecontactyourlocalserviceagent.
5.4. When not in use place the fan in its original box or otherwise cover to protect from dust, and store in a safe, dry, childproof
location.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Original Language Version
©JackSealeyLimited
HVD30.V3 Issue 2 (3) 01/03/2020