Sealey TST10 - User Manual

To Next Page

TEMPORARY PUNCTURE REPAIR KIT

MODEL NO: TST10

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

1.1. SAFETY INFORMATION FOR WHOLE KIT

  WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this tool.

  WARNING! This kit contains flammable glue. If you require a safety data sheet, contact your Sealey stockist.

 WARNING! Familiarise yourself with the specific applications and limitations of the kit, as well as any potential hazards.

9 This kit should be used in conjunction with inspection maintenance procedures recommended in the vehicle manufacturer’s manual.

9 Ensure that the kit is correct for the task.

9 Wear the appropriate personal protective equipment for the task. A full range is available from your Sealey stockist.

8 DO NOT use the kit for any purpose other than that for which it is designed.

9 Ensure that the vehicle is properly supported with axle stands before working under the vehicle.

9  Ensure there is adequate lighting prior to using the kit. A range of inspection lamps are available from your Sealey stockist.

9 Keep children and unauthorised persons away from the working area.

9  DO NOT use the kit if any parts are damaged or missing, as this may cause failure and/or personal injury.

9  DO NOT use the kit when you are tired, or under the influence of alcohol, drugs or intoxicating medication.

9 After use, store in a safe, dry childproof area.

1.2. SAFETY INFORMATION FOR REPAIR SOLUTION

Contents of the Repair Solution do not exceed 125 ml, Hazard Statements and Precautionary Statements have been omitted from the

product label.

Signal Word: DANGER

HAZARD STATEMENTS:

9  Highlyammableliquidandvapour.

9 May be fatal if swallowed and enters airways.

9 Causes skin irritation.

9 May cause drowsiness or dizziness.

9 Very toxic to aquatic life, with long lasting effects.

PRECAUTIONARY STATEMENTS:

9  Keepawayfromheat/sparks/openames/hotsurfaces.–Nosmoking.

9 Keep container tightly closed.

9 Ground/bond container and receiving equipment.

9 Use explosion-proof electrical/ventilating/lighting equipment.

9 Use only non-sparking tools.

9 Take precautionary measures against static discharges.

9 Avoid breathing dust/fume/gas/mist/vapours/spray.

9 Use only outdoors or in a well-ventilated area.

9 Avoid release into the environment.

9 Wash hands thoroughly after use.

9 Wear protective gloves/protective clothing/eye protection/face protection.

9 Avoid release into the environment.

9 Wash hands thoroughly after use.

9 IF ON SKIN (or hair): Remove/take off immediately all contaminated clothing.

9 Rinse with water/shower.

9  Incaseofre:Usepowder,foam,carbondioxideforextinction.

9 Store in a well ventilated place. Keep cool.

9 Keep container tightly closed

9 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing

9 Call a POISON CENTRE or doctor/physician if you feel unwell.

9 If skin irritation occurs: Get medical advice/attention.

9 Take off contaminated clothing and wash before reuse

9 IF SWALLOWED: Immediately call a POISON CENTRE or doctor/physician.

8 DO NOT induce vomiting.

9 Collect spillage.

Refer to

instruction

manual

Wear eye

protection

Wear protective

gloves

Wear protective

clothing

HarmfulHighly

flammable

liquid & vapour

May be fatal if

swallowed and

enters airways

Very toxic to

aquatic life with

long lasting

effects

Original Language Version

Safety symbols referring to Repair Solution

TST10 | Issue:4 (1) 05/05/20

Need help?

Do you have a question about the Sealey TST10 and is the answer not in the manual?

Summary

SAFETY

SAFETY INFORMATION FOR WHOLE KIT

General safety advice and precautions for using the entire temporary puncture repair kit.

SAFETY INFORMATION FOR REPAIR SOLUTION

Details hazard statements and precautionary measures for the repair solution.

Summary

SAFETY

SAFETY INFORMATION FOR WHOLE KIT

General safety advice and precautions for using the entire temporary puncture repair kit.

SAFETY INFORMATION FOR REPAIR SOLUTION

Details hazard statements and precautionary measures for the repair solution.

Overview

Function Description
Important Technical Specifications
Usage Features
Safety Information (General Kit)
Safety Information (Repair Solution - Glue)
Maintenance Features
Warranty

The Sealey TST10 Temporary Puncture Repair Kit is designed for repairing punctures in tubeless tyres, particularly those on agricultural and off-road vehicles. It can also serve as a temporary or emergency fix for punctures on cars and commercial vehicles, allowing the tyre to be repaired without removal from the wheel. It is crucial to note that this kit is not to be used as a permanent repair for road vehicles.

Function Description:

The kit provides the necessary tools and materials to quickly seal a puncture in a tubeless tyre. The process involves preparing the puncture site, inserting a repair strip coated with glue, and then securing the strip within the tyre to create a seal. This allows for immediate repair, enabling the vehicle to be moved or used until a permanent repair can be performed.

Important Technical Specifications:

Model No.: TST10
Contents: The kit includes a rasp, an insertion needle, 30 repair strips, and 20g of glue.
Glue Volume: The Repair Solution (glue) contents do not exceed 125 ml.

Usage Features:

The kit's operation is straightforward and designed for quick application:

Object Removal: If an object caused the puncture, it must be removed from the tyre.
Collar Attachment: A collar is fitted onto the insertion needle by loosening a grub screw with a hex key.
Puncture Preparation: The puncture hole is cleaned and widened using the rasp.
Strip Insertion: A repair strip is fitted into the middle of the insertion needle, with 50% protruding from each end.
Glue Application: The repair strip is covered with the provided glue.
Tyre Insertion: The insertion needle, with the glued strip, is pushed most of the way through the tyre, leaving approximately 20mm of the strip sticking out.
Needle Removal: As the insertion needle is pulled back out, the collar is pushed down to nip the strip, ensuring the strip remains in the tyre.
Finishing: A loop and two ends of the strip will protrude from the tyre, which then need to be cut off.
Storage: After use, the kit items should be cleaned, the protector removed from the insertion needle, and the kit stored in a safe, childproof location.

Safety Information (General Kit):

Adherence to Regulations: Always ensure compliance with Health & Safety, local authority, and general workshop practice regulations.
Flammable Glue: The kit contains flammable glue. A Safety Data Sheet (SDS) can be obtained from a Sealey stockist if required.
Familiarisation: Users must familiarise themselves with the kit's applications, limitations, and potential hazards.
Maintenance Procedures: The kit should be used in conjunction with inspection and maintenance procedures recommended in the vehicle manufacturer's manual.
Correct Task: Ensure the kit is suitable for the specific task.
Personal Protective Equipment (PPE): Appropriate PPE must be worn. A full range is available from Sealey stockists.
Intended Use: Do not use the kit for any purpose other than its designed function.
Vehicle Support: Ensure the vehicle is properly supported with axle stands before working underneath it.
Adequate Lighting: Ensure sufficient lighting. Inspection lamps are available from Sealey stockists.
Exclusion of Others: Keep children and unauthorised persons away from the working area.
Damaged/Missing Parts: Do not use the kit if any parts are damaged or missing, as this could lead to failure or injury.
User Condition: Do not use the kit when tired or under the influence of alcohol, drugs, or intoxicating medication.
Storage: After use, store the kit in a safe, dry, childproof area.

Safety Information (Repair Solution - Glue):

Signal Word: DANGER
Hazard Statements:
- Highly flammable liquid and vapour.
- May be fatal if swallowed and enters airways.
- Causes skin irritation.
- May cause drowsiness or dizziness.
- Very toxic to aquatic life with long lasting effects.
Precautionary Statements:
- Prevention:
  - Keep away from heat/sparks/open flames/hot surfaces. – No smoking.
  - Keep container tightly closed.
  - Ground/bond container and receiving equipment.
  - Use explosion-proof electrical/ventilating/lighting equipment.
  - Use only non-sparking tools.
  - Take precautionary measures against static discharges.
  - Avoid breathing dust/fume/gas/mist/vapours/spray.
  - Use only outdoors or in a well-ventilated area.
  - Avoid release into the environment.
  - Wash hands thoroughly after use.
  - Wear protective gloves/protective clothing/eye protection/face protection.
- Response:
  - IF ON SKIN (or hair): Remove/take off immediately all contaminated clothing. Rinse with water/shower.
  - In case of fire: Use powder, foam, carbon dioxide for extinction.
  - IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTRE or doctor/physician if you feel unwell.
  - If skin irritation occurs: Get medical advice/attention.
  - Take off contaminated clothing and wash before reuse.
  - IF SWALLOWED: Immediately call a POISON CENTRE or doctor/physician. DO NOT induce vomiting.
  - Collect spillage.
- Storage:
  - Store in a well-ventilated place. Keep cool.
  - Keep container tightly closed.
- Disposal:
  - Store locked up.
  - Dispose of contents/container in accordance with local regulation.

Maintenance Features:

Cleaning: After each use, the items in the kit should be cleaned.
Protector Removal: The protector should be removed from the insertion needle after use.
Storage: The kit should be stored in a safe, dry, childproof area to maintain its condition and prevent accidental access.
Environmental Protection: Unwanted materials should be recycled. All tools, accessories, and packaging should be sorted and taken to a recycling centre. When the product becomes unserviceable, any fluids (if applicable) should be drained into approved containers and disposed of according to local regulations.

Warranty:

The product comes with a 12-month guarantee from the purchase date. Proof of purchase is required for any claim. Sealey Group reserves the right to alter data, specifications, and component parts without prior notice as part of their policy to continually improve products. No liability is accepted for incorrect use of this product.