Sears CRAFTSMAN 944.602000 User Manual (English)

Questions and Answers:

L
Lauren MosesAug 17, 2025
How to troubleshoot a Sears Lawn Mower that is hard to start?
- J
  jrichardsonAug 18, 2025
  If your Sears Lawn Mower is hard to start, several factors could be the cause. Start by checking the air filter and clean or replace it if it’s dirty. Replace the spark plug if it is bad. Ensure the battery is fully charged; recharge or replace if weak or dead. Other causes include a dirty fuel filter (replace it), stale or dirty fuel (drain and refill with fresh gasoline), or loose/damaged wiring (check all wiring). If these steps don't resolve the issue, the carburetor or engine valves may need adjustment, in which case you should contact an authorized service center/department.
C
Charles WalkerAug 20, 2025
What to do if my Sears Lawn Mower engine will not turn over?
- X
  xjenkinsAug 20, 2025
  If your Sears Lawn Mower engine won't turn over, make sure the brake pedal is depressed and the attachment clutch is disengaged. Check the battery; recharge or replace it if it's weak or dead. Also, inspect the fuse and replace it if blown. Clean corroded battery terminals and check all wiring for any loose or damaged connections. If the issue persists, the ignition switch, solenoid, or starter might be faulty and need to be checked or replaced. For faulty operator presence switch(es), contact an authorized service center/department.
L
lincolleenAug 23, 2025
What to do if my Sears Lawn Mower engine clicks but will not start?
- B
  Brittany JacksonAug 23, 2025
  If your Sears Lawn Mower engine clicks but won't start, the issue is likely related to the battery or starter system. First, try recharging or replacing the battery if it's weak or dead. Then, clean any corrosion from the battery terminals. Also, check all wiring for loose or damaged connections. If the problem continues, the solenoid or starter may be faulty and need to be checked or replaced.
M
Mary HaleAug 25, 2025
Why does my Sears Lawn Mower engine “backfire” when turning engine “OFF”?
- L
  Lori WillisAug 26, 2025
  To prevent your Sears Lawn Mower engine from backfiring when turning it off, move the throttle control to the “SLOW” position and allow the engine to idle for 30 seconds before stopping it.
T
Tiffany MartinezAug 30, 2025
Why does my Sears Lawn Mower have excessive vibration?
- N
  nichole54Aug 30, 2025
  If your Sears Lawn Mower exhibits excessive vibration, inspect the blade for wear, bends, or looseness; replace the blade and tighten the blade bolt if necessary. If the blade mandrel is bent, replace it. Also, check for any loose or damaged parts and tighten or replace them as needed.
L
Lisa KiddSep 1, 2025
Why does my Sears Lawn Mower have poor grass discharge?
- M
  Matthew SimpsonSep 1, 2025
  If your Sears Lawn Mower isn't discharging grass properly, ensure the throttle control is in the “FAST” position and shift to a slower speed if you're moving too quickly. Allow the grass to dry before mowing if it's wet. Level the mower deck and check the tires for proper air pressure. Replace or sharpen the blade and tighten the blade bolt if the blade is worn, bent, or loose. Clean the underside of the mower housing to remove any buildup of grass, leaves, and trash. Replace the mower drive belt if it's worn. Reinstall the blades with the sharp edge down if they're improperly installed and replace with the blades listed in this manual if the wrong blades are being used. Clean around mandrels to open vent holes if the mower deck vent holes are clogged.
R
Robert SolisSep 4, 2025
Why is my Sears Lawn Mower cutting grass unevenly?
- B
  Brad AustinSep 4, 2025
  If your Sears Lawn Mower is providing a poor, uneven cut, start by checking the blade. Replace it if it's worn, bent, or loose, and ensure the blade bolt is tightened. Next, level the mower deck. Remove any buildup of grass, leaves, and trash from under the mower. If the blade mandrel is bent, replace it. Finally, clean around the mandrels to open vent holes if they are clogged with grass, leaves, and trash.
Z
Zachary AustinSep 7, 2025
Why are the headlights not working on my Sears Lawn Mower?
- K
  Kerri SalasSep 7, 2025
  If the headlight(s) on your Sears Lawn Mower aren't working, first ensure the switch is turned “ON”. If that doesn't solve the issue, replace any burned-out bulb(s) or lamp(s). If the light switch is faulty, check or replace it. Inspect the wiring and connections for any looseness or damage. Lastly, check the fuse and replace it if it's blown.
K
Kristin PriceSep 9, 2025
What to do if mower blades will not rotate on my Sears Lawn Mower?
- K
  Kimberly HernandezSep 9, 2025
  If the mower blades on your Sears Lawn Mower won't rotate, check for any obstruction in the clutch mechanism and remove it. If there is no obstruction, replace the mower drive belt if it's worn or damaged. Also, replace the idler pulley if it's frozen, and replace the blade mandrel if it's frozen.

Sears CRAFTSMAN 944.602000 Specifications

General

Brand	Sears
Model	CRAFTSMAN 944.602000
Category	Lawn Mower
Language	English

Summary

SAFETY RULES

GENERAL OPERATION

Detailed instructions for safe operation of the tractor.

SLOPE OPERATION

Precautions and methods for safe operation on inclines.

CHILDREN SAFETY

Safety guidelines to prevent accidents involving children.

SERVICE SAFETY

Safety considerations during maintenance and repair.

PRODUCT SPECIFICATIONS

WARRANTY

LIMITED TWO (2) YEAR WARRANTY ON CRAFTSMAN TRACTOR

Details of the warranty coverage for the riding equipment.

FULL ONE (1) YEAR WARRANTY ON BATTERY

Specific warranty terms for the tractor's battery.

COMMERCIAL OR RENTAL USE WARRANTY

Warranty limitations for commercial or rental applications.

MAINTENANCE AGREEMENT

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

List of tools needed for tractor assembly.

UNPACKING AND PREPARATION

Steps for removing the tractor from its packaging and skid.

CONNECTING THE BATTERY

Procedure for safely connecting the tractor's battery.

ASSEMBLY

INSTALLING THE SEAT

Instructions for attaching and adjusting the tractor seat.

REMOVING TRACTOR FROM SKID

Guidance on safely moving the tractor off its shipping skid.

ASSEMBLING MOWER DECK GAUGE WHEELS

Steps to attach and adjust gauge wheels to the mower deck.

ASSEMBLY

ATTACHING THE NOSE ROLLER

Procedure for installing the nose roller assembly.

INSTALLING MOWER AND DRIVE BELT

Instructions for mounting the mower and routing the drive belt.

ASSEMBLY

FINAL CHECKS AND PREPARATION

Steps to check tire pressure, brake system, and review assembly checklist.

OPERATION

KNOW YOUR TRACTOR

Overview of the tractor and its main components.

TRACTOR CONTROLS AND INDICATORS

Detailed explanation of each control and indicator on the dashboard and steering.

OPERATION

OPERATING PROCEDURES

Instructions for using the parking brake, stopping, and basic controls.

ADJUSTING MOWER HEIGHT

How to set the desired cutting height for the mower deck.

OPERATION

ADJUSTING GAUGE WHEELS

Steps to adjust mower deck gauge wheels for proper cutting.

OPERATING THE MOWER

Instructions for engaging and disengaging the mower blades.

OPERATING ON HILLS

Safety precautions and methods for operating on slopes.

TRANSPORTING THE TRACTOR

Guidelines for safely pushing or towing the tractor.

OPERATION

TOWING AND ATTACHMENTS

Recommendations for towing carts and other attachments.

PRE-START CHECKS AND ENGINE STARTING

Procedures for checking oil, fuel, and starting the engine.

OPERATION

TRANSMISSION WARM-UP AND PURGE

Steps for warming up and purging the automatic transmission.

MOWING TIPS AND TECHNIQUES

Advice for optimal mowing performance and grass cutting.

CUSTOMER RESPONSIBILITIES

MAINTENANCE AND LUBRICATION SCHEDULES

Recommended maintenance tasks, frequencies, and lubrication points.

GENERAL RECOMMENDATIONS AND PRE-USE CHECKS

General advice for tractor maintenance and essential pre-operation checks.

CUSTOMER RESPONSIBILITIES

TRACTOR, BRAKE, TIRE, AND BATTERY CARE

Maintenance and checks for tractor systems, brakes, tires, and battery.

OPERATOR PRESENCE SYSTEM AND BLADE SERVICE

Ensuring safety systems function and servicing mower blades.

CUSTOMER RESPONSIBILITIES

BATTERY TERMINALS, BELTS, COOLING, AND FLUIDS

Cleaning battery terminals, maintaining belts, cooling systems, and fluid levels.

ENGINE OIL CHANGE AND AIR/COOLING AREA CLEANING

Procedures for oil changes and cleaning engine air intake and cooling areas.

CUSTOMER RESPONSIBILITIES

AIR FILTER, SPARK PLUGS, AND FUEL FILTER SERVICE

Maintenance for air filter, spark plugs, and fuel filter replacement.

GENERAL CLEANING AND PROTECTION

Tractor exterior cleaning and protecting painted surfaces.

SERVICE AND ADJUSTMENTS

MOWER DECK REMOVAL AND INSTALLATION

Step-by-step instructions for removing and installing the mower deck.

SERVICE AND ADJUSTMENTS

MOWER HOUSING LEVELING PROCEDURES

Methods for leveling the mower housing side-to-side.

SERVICE AND ADJUSTMENTS

FRONT-TO-BACK MOWER ADJUSTMENT

Adjusting the mower deck for optimal front-to-back blade height.

SERVICE AND ADJUSTMENTS

DRIVE BELT REPLACEMENT AND BRAKE ADJUSTMENT

Procedures for replacing drive belts and adjusting the tractor brakes.

SERVICE AND ADJUSTMENTS

MOTION DRIVE BELT, TRANSMISSION, STEERING, AND WHEEL SERVICE

Maintenance for drive belts, transmission, steering alignment, and wheel repairs.

JUMP-STARTING PROCEDURES

Guideline for jump-starting the tractor with a weak battery.

SERVICE AND ADJUSTMENTS

HEADLIGHTS, INTERLOCKS, FUSES, AND HOOD/GRILL SERVICE

Replacing headlights, checking wiring, fuses, and removing the hood/grill assembly.

SERVICE AND ADJUSTMENTS

CHOKE CONTROL AND CARBURETOR ADJUSTMENTS

Adjusting the choke control and carburetor for optimal engine performance.

STORAGE

TRACTOR AND ENGINE STORAGE PREPARATION

Steps for preparing the tractor and engine for long-term storage.

TROUBLESHOOTING

ENGINE STARTING AND POWER ISSUES

Causes and corrections for engine starting problems, loss of power, and vibration.

TROUBLESHOOTING

CUTTING, DISCHARGE, AND ELECTRICAL/DRIVE PROBLEMS

Solutions for poor cut, discharge issues, battery charging, and drive system faults.

SCHEMATIC

TRACTOR ELECTRICAL SCHEMATIC

Wiring diagram illustrating the tractor's electrical system components.

REPAIR PARTS

ELECTRICAL COMPONENTS

Illustrated parts breakdown for the tractor's electrical system.

REPAIR PARTS

CHASSIS AND ENCLOSURES PARTS

Illustrated parts breakdown for the tractor's chassis and body components.

REPAIR PARTS

DRIVE SYSTEM PARTS

Illustrated parts breakdown for the tractor's drive system components.

REPAIR PARTS

STEERING ASSEMBLY PARTS

Illustrated parts breakdown for the tractor's steering assembly.

REPAIR PARTS

SEAT ASSEMBLY PARTS

Illustrated parts breakdown for the tractor's seat assembly.

REPAIR PARTS

DECALS AND WHEELS/TIRES PARTS

Illustrated parts breakdown for tractor decals and wheel/tire components.

REPAIR PARTS

ENGINE COMPONENTS

Illustrated parts breakdown for the tractor's engine.

REPAIR PARTS

MOWER LIFT MECHANISM PARTS

Illustrated parts breakdown for the mower lift system.

REPAIR PARTS

MOWER DECK ASSEMBLY PARTS

Illustrated parts breakdown for the mower deck assembly.

REPAIR PARTS

HYDRO GEAR TRANSAXLE COMPONENTS

Illustrated parts breakdown for the Hydro Gear transaxle.

REPAIR PARTS

KOHLER ENGINE CYLINDER HEAD AND CRANKCASE PARTS

Illustrated parts breakdown for Kohler engine cylinder head and crankcase.

REPAIR PARTS

KOHLER ENGINE IGNITION, BLOWER HOUSING, AND AIR INTAKE PARTS

Illustrated parts breakdown for engine ignition, blower housing, and air intake.

REPAIR PARTS

KOHLER ENGINE STARTING SYSTEM, CONTROLS, AND OIL PAN PARTS

Illustrated parts breakdown for engine starting, controls, and lubrication systems.

REPAIR PARTS

KOHLER ENGINE CRANKSHAFT, EXHAUST, AND FUEL SYSTEM PARTS

Illustrated parts breakdown for engine crankshaft, exhaust, and fuel system.

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

Related product manuals

Sears CRAFTSMAN 944.602131

52 pages

Sears CRAFTSMAN 944.602151

52 pages

Sears CRAFTSMAN 944.602900

60 pages

Sears CRAFTSMAN 944.601090

52 pages

Sears CRAFTSMAN 944.608340

52 pages

Sears CRAFTSMAN 944.604150

48 pages

Sears CRAFTSMAN 944.600750

60 pages

Sears CRAFTSMAN 944.604110

52 pages

Sears CRAFTSMAN 944.603050

60 pages

Sears CRAFTSMAN 944.605900

52 pages

Sears CRAFTSMAN 944.601080

52 pages

Sears Craftsman EZ3 944.609191

52 pages

Sears CRAFTSMAN 944.602000 User Manual

Table of Contents

Questions and Answers:

Sears CRAFTSMAN 944.602000 Specifications

Summary

SAFETY RULES

GENERAL OPERATION

SLOPE OPERATION

CHILDREN SAFETY

SERVICE SAFETY

PRODUCT SPECIFICATIONS

WARRANTY

LIMITED TWO (2) YEAR WARRANTY ON CRAFTSMAN TRACTOR

FULL ONE (1) YEAR WARRANTY ON BATTERY

COMMERCIAL OR RENTAL USE WARRANTY

MAINTENANCE AGREEMENT

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

UNPACKING AND PREPARATION

CONNECTING THE BATTERY

ASSEMBLY

INSTALLING THE SEAT

REMOVING TRACTOR FROM SKID

ASSEMBLING MOWER DECK GAUGE WHEELS

ASSEMBLY

ATTACHING THE NOSE ROLLER

INSTALLING MOWER AND DRIVE BELT

ASSEMBLY

FINAL CHECKS AND PREPARATION

OPERATION

KNOW YOUR TRACTOR

TRACTOR CONTROLS AND INDICATORS

OPERATION

OPERATING PROCEDURES

ADJUSTING MOWER HEIGHT

OPERATION

ADJUSTING GAUGE WHEELS

OPERATING THE MOWER

OPERATING ON HILLS

TRANSPORTING THE TRACTOR

OPERATION

TOWING AND ATTACHMENTS

PRE-START CHECKS AND ENGINE STARTING

OPERATION

TRANSMISSION WARM-UP AND PURGE

MOWING TIPS AND TECHNIQUES

CUSTOMER RESPONSIBILITIES

MAINTENANCE AND LUBRICATION SCHEDULES

GENERAL RECOMMENDATIONS AND PRE-USE CHECKS

CUSTOMER RESPONSIBILITIES

TRACTOR, BRAKE, TIRE, AND BATTERY CARE

OPERATOR PRESENCE SYSTEM AND BLADE SERVICE

CUSTOMER RESPONSIBILITIES

BATTERY TERMINALS, BELTS, COOLING, AND FLUIDS

ENGINE OIL CHANGE AND AIR/COOLING AREA CLEANING

CUSTOMER RESPONSIBILITIES

AIR FILTER, SPARK PLUGS, AND FUEL FILTER SERVICE

GENERAL CLEANING AND PROTECTION

SERVICE AND ADJUSTMENTS

MOWER DECK REMOVAL AND INSTALLATION

SERVICE AND ADJUSTMENTS

MOWER HOUSING LEVELING PROCEDURES

SERVICE AND ADJUSTMENTS

FRONT-TO-BACK MOWER ADJUSTMENT

SERVICE AND ADJUSTMENTS

DRIVE BELT REPLACEMENT AND BRAKE ADJUSTMENT

SERVICE AND ADJUSTMENTS

MOTION DRIVE BELT, TRANSMISSION, STEERING, AND WHEEL SERVICE

JUMP-STARTING PROCEDURES

SERVICE AND ADJUSTMENTS

HEADLIGHTS, INTERLOCKS, FUSES, AND HOOD/GRILL SERVICE

SERVICE AND ADJUSTMENTS

CHOKE CONTROL AND CARBURETOR ADJUSTMENTS

STORAGE

TRACTOR AND ENGINE STORAGE PREPARATION

TROUBLESHOOTING

ENGINE STARTING AND POWER ISSUES

TROUBLESHOOTING

CUTTING, DISCHARGE, AND ELECTRICAL/DRIVE PROBLEMS

SCHEMATIC