Seastar Solutions Hynautic 04 Series - Page 20

16
Hynautic Hydraulic Engine Controls – 04 Series
FILLING AND BLEEDING
HYNAUTIC CONTROLS
vÌiÀÊLii`}ÊÃÞÃÌiÊ>ÌÊi>VÊÃ>ÛiÊLii`iÀÊÛ>Ûi]Êi>VÊÃi`iÀÊ
ÕÃÌÊÜÊLiÊLi`°ÊÊÃ>Ê>ÕÌÊvÊ>ÀÊÜÊLiÊÌÀ>««i`Ê>ÌÊÌiÊ}Ê
«ÌÊÊi>VÊÃi`iÀÊi>`°
1Ê ,iwÊÀiÃiÀÛÀÊvÊÀiµÕÀi`ÊwÊÌ>Ê>ÌÊÌÃÊÌiÊÌÊLiÌÜiiÊ£ÉÓÊ>`Ê
ÓÉÎÊvÕ®]Ê>`Êi>ÛiÊ>LÕÌÊ£ääÊ«ÃÊÊÌiÊ«ÀiÃÃÕÀiÊ}>Õ}i°
Place a rag over the bleeder hole on the sender, to prevent fluid from
spilling on the console.
2Ê 6iÀÞÊÃÜÞÊ«iÊÌiÊLii`iÀÊ«Õ}ÊÕÃ}Ê>ÊÎɣȸÊ>iÊÜÀiV°Ê
-iiÊ}ÕÀiÊ£äÊvÀÊV>ÌÊvÊLii`iÀÊÃVÀiÜ°
Bleeding the System at
Senders
NOTICE
GASKET
BLEEDER SCREW
Figure 20. Bleeder Screw.
3Ê ÜÊÌiÊyÕ`ÊÌÊLii`ÊÕÌÊÕÌÊÌiÊyÕ`ÊÃÊVi>ÀÊÜÌÕÌÊ>ÀÊ
LÕLLið
4Ê /}ÌiÊÌiÊLii`iÀÊÃVÀiÜÊ>vÌiÀÊLii`}°
5Ê ,i«i>ÌÊ-Ìi«ÃÊ£ÊÌÊ{Ê>LÛi]ÊvÀÊi>VÊÃi`iÀ°
6Ê /iÊÀiÃiÀÛÀÊiÛiÊÃÕ`ÊLiÊLiÌÜiiÊ£ÉÓÊ>`ÊÓÉÎÊvÕ°ÊvÊÌiÊ
iÛiÊÃÊLiÜÊÌÃ]ÊÌiÊÀiÃiÀÛÀÊÃÕ`ÊLiÊwi`ÊÌÊÌÃÊiÛi°Ê
6iÀvÞÊÌ>ÌÊ«ÀiÃÃÕÀâiÊÊÌiÊÀiÃiÀÛÀÊÃÊLiÌÜiiÊnäÊ>`ÊnxÊ«Ã°