Sebart Mini Avanti User Manual

SebArt professional line Mini Avanti
1.4m ARF Jet for EDF or P20 micro-turbine
Instruction Manual
The all new Mini Avanti Jet 1.4m ARF was designed by Italian champion aerobatic pilot Sebastiano
Silvestri. This sport ARF jet-model design is based on the Hawk full size aircraft design and modified
by adding the ultimate aerodynamic ideas of modern pattern models and using Seba’s 15 years
experience in flying jets.... the result is surprising! This innovative design combined with the
lightweight structure, the fiberglass fuselage and all wood airframe wings and stabs, give the Mini
Avanti Jet 1.4m ARF an impressive precision and smoothness at any airspeed and flight condition.
Thanks to this low wing loading and the powerful 90mm 12 blades EDF or the P20 micro-turbine, it
can be a fantastic aerobatic jet-trainer… you will be amazed with your new Mini Avanti Jet ARF !
.....the only aerobatic limit to unlimited fun is your imagination!
Specifications:
Wing span: 1360 mm
Length: 1420 mm
Wing area: 38 sq. dm.
Radio: Minimum 6 channel
Weight with recommended power set up:
EDF: Weight (less battery): 2,900g Weight RTF (with 5800-6S): 3,800g 90mm 12 blades aluminium
EDF unit, 1750 Kw motor, 130A ESC with 8A BEC 5V
Micro-turbine P20: Weight (empty, less RX and Turbine battery): 3,050g Weight RTF (with 800-2S RX
batt. and turbine batt. + 650cc tank full): 3,700g
Conversion turbine set (including tank, thrust tube and other accessories) is available as an option
(item # A140-17)
Required radio system: • Minimum 6-channel radio system (better 9ch) • 7 micro servos 17gm for
elevators, ailerons, flaps and rudder • 3 servos for doors and steering , the door sequencer and the
electric retracts are factory installed • full extension set are available in the optional servo set (item
# A140-12 set)
Recommended Li-Po battery pack for best performance with EDF: • 5000-6S or 5800-6S Minimum 20
C-rate
Additional required tools: • Drill • Drill bits: 1,5mm • Phillips screwdriver • Hobby knife • Sanding
paper • Masking tape • Soldering iron
Additional required adhesives: • thin CA • medium CA • epoxy 5minutes • epoxy 20 minutes •
silicon

Sebart Mini Avanti Specifications

General

Brand	Sebart
Model	Mini Avanti
Category	Toy
Language	English

Summary

Specifications

Weight With Recommended Power Setup

Details recommended weights for EDF and micro-turbine configurations, including components.

Required Radio System

Specifies a minimum 6-channel radio system, micro servos, and optional accessories for installation.

Recommended Li-Po Battery Pack for EDF

Suggests 5000-6S or 5800-6S Li-Po batteries with a minimum 20 C-rate for optimal EDF performance.

Radio Setup and Flight Controls

Radio Setup Recommendations

Recommends using a 3-axis gyro system for more realistic and stable jet flying.

Flaps Usage

Advises using flaps down for take-off and landings to shorten and ease these phases.

Control Throws

Provides recommended throws and expo settings for aileron, elevator, and rudder for various flight modes.

Control Mixing

Suggests mixing rudder to elevator down and to ailerons for specific flight characteristics.

Centre of Gravity (CG)

Specifies the recommended CG location as 145mm behind the leading edge of the wing.

Pre-flight Checks

Throttle Management

Warns against full throttle dives and stresses the necessity of throttle management for airframe integrity.

Radio Range Test

Emphasizes performing a radio range test, checking control directions, and ensuring battery charge before flight.