Selenium DT 2006S - Page 8

B) Repeat procedure A in order to confirm the password and the system will be
blocked. If the password is not the same, the operation will be canceled.
C) The correct password must be given and press ENTER to unblock the sys
3-Sub-menu SYSTEM
Push the “Menu” button and then BACK/NEXT and ENTER to access the Sub
menu SYSTEM.
A)
The first option is INPUT OPTION that makes it possible to link the input
channels (A and B). With this option enabled, every change made to chann
A will be automatically applied to channel B.
B)
The second option is WAKE UP. This option makes it possible to choose the
signal's behavior as soon as the DT2006S is turned on. FADE
possible to gradually increase the signal's volume. MUTE HOLD
DT2006S with the MUTE buttons on.
C)
The option DELAY TIME/DISTANCE makes it possible to choose the unit in
which the delay time will be shown (time in ms, meters or feet).
D)
The option INTERFACE makes it possible to adjust the baud rate and the
addressing code (ID). The baud rate options are 2400, 4800, 9600, 19200,
and 38400. The ID can be set between 1 and 32.
4- Adjust the PARAMETERS
To adjust the parameters of a crossover, press the button GAIN and use buttons
BACK/NEXT and ENTER to scr
adjust the parameter value.
1- INPUT GAIN
–
2-
OUTPUT GAIN
3- POLARITY –
B) Repeat procedure A in order to confirm the password and the system will be
blocked. If the password is not the same, the operation will be canceled.
C) The correct password must be given and press ENTER to unblock the sys
Push the “Menu” button and then BACK/NEXT and ENTER to access the Sub
The first option is INPUT OPTION that makes it possible to link the input
channels (A and B). With this option enabled, every change made to chann
A will be automatically applied to channel B.
The second option is WAKE UP. This option makes it possible to choose the
signal's behavior as soon as the DT2006S is turned on. FADE
possible to gradually increase the signal's volume. MUTE HOLD
DT2006S with the MUTE buttons on.
The option DELAY TIME/DISTANCE makes it possible to choose the unit in
which the delay time will be shown (time in ms, meters or feet).
The option INTERFACE makes it possible to adjust the baud rate and the
addressing code (ID). The baud rate options are 2400, 4800, 9600, 19200,
and 38400. The ID can be set between 1 and 32.
To adjust the parameters of a crossover, press the button GAIN and use buttons
BACK/NEXT and ENTER to scr
oll the menus and rotate the PARAMETERS button in order to
–
this parameter accepts values from -
40dB to +6dB.
OUTPUT GAIN
– this parameter accepts values from
-
output channel polarity selected (+ or -)
8
B) Repeat procedure A in order to confirm the password and the system will be
blocked. If the password is not the same, the operation will be canceled.
C) The correct password must be given and press ENTER to unblock the sys
tem.
Push the “Menu” button and then BACK/NEXT and ENTER to access the Sub
-
The first option is INPUT OPTION that makes it possible to link the input
channels (A and B). With this option enabled, every change made to chann
el
The second option is WAKE UP. This option makes it possible to choose the
signal's behavior as soon as the DT2006S is turned on. FADE
-IN makes it
possible to gradually increase the signal's volume. MUTE HOLD
starts up the
The option DELAY TIME/DISTANCE makes it possible to choose the unit in
which the delay time will be shown (time in ms, meters or feet).
The option INTERFACE makes it possible to adjust the baud rate and the
addressing code (ID). The baud rate options are 2400, 4800, 9600, 19200,
To adjust the parameters of a crossover, press the button GAIN and use buttons
oll the menus and rotate the PARAMETERS button in order to
40dB to +6dB.
-
40dB to +6dB.