N
Nicole AndrewsAug 14, 2025
What to do if my Senco Power Tool has a weak drive?
- EErin MeyerAug 14, 2025
If your Senco Power Tool exhibits a weak drive, verify that the air supply is adequate, lubricate the tool, or replace parts marked with "C."
To Next PageTo Next PageWhat to do if my Senco Power Tool has a weak drive?
If your Senco Power Tool exhibits a weak drive, verify that the air supply is adequate, lubricate the tool, or replace parts marked with "C."
What to do if my Senco Power Tool is jamming?
If your Senco Power Tool is jamming, clean the tool. Alternatively, lubricate the feeder pawl and feed piston, or replace parts marked with "D."
What to do if my Senco Power Tool has poor feed?
If your Senco Power Tool has poor feed, clean the tool and check the magazine adjustment. You may also need to lubricate the feeder pawl and feed piston, or replace parts marked with “D.”
What to do if my Senco Power Tool is operating sluggishly?
If your Senco Power Tool is operating sluggishly, lubricate the tool or replace parts marked by letter “A.”
What to do if my Senco Power Tool has poor return?
If your Senco Power Tool demonstrates poor return, clean and lubricate the tool, or replace parts marked with “B.”
How to fix an air leak near the bottom of my Senco Power Tool?
To fix an air leak near the bottom of your Senco Power Tool, tighten the screws or replace the parts marked by the letter “B.”
How to fix an air leak near the top of my Senco Power Tool?
To fix an air leak near the top of your Senco Power Tool, tighten the screws or replace the parts marked by letter “A.”
What to do if my Senco Power Tool driver is broken or worn?
If the driver of your Senco Power Tool is broken or worn, replace the parts marked by “C.”
What to do if my Senco Power Tool does nothing?
If your Senco Power Tool does nothing, verify the air supply or replace parts marked by letter “A.”
Press latch and lift gate to open magazine for loading or adjustment.
Depress, hold, and turn pins to set desired nail collation type.
Explains two firing modes: trigger-only and safety-contact (bottom-fire).
Details using the restrictive trigger for precise fastener placement.
Procedure for adjusting fastener drive depth using the adjustment wheel.
How to rotate the deflector to change the direction of exhaust air.
Steps for disconnecting air supply and removing jammed fasteners.
Covers daily checks, lubrication with pneumatic oil, and cleaning procedures.
Addresses common issues of air leaks near the top and bottom of the tool.
Solutions for when the tool does not function or operates slowly.
Diagnoses and resolves problems with the driver's return stroke.
Covers weak drive, broken drivers, poor feed, and tool jamming.
Guidance for unresolved problems, directing users to contact Senco.
Outlines warranty coverage, conditions for honoring, and exclusions.
Details the process for replacing tools lost to natural disasters.
Press latch and lift gate to open magazine for loading or adjustment.
Depress, hold, and turn pins to set desired nail collation type.
Explains two firing modes: trigger-only and safety-contact (bottom-fire).
Details using the restrictive trigger for precise fastener placement.
Procedure for adjusting fastener drive depth using the adjustment wheel.
How to rotate the deflector to change the direction of exhaust air.
Steps for disconnecting air supply and removing jammed fasteners.
Covers daily checks, lubrication with pneumatic oil, and cleaning procedures.
Addresses common issues of air leaks near the top and bottom of the tool.
Solutions for when the tool does not function or operates slowly.
Diagnoses and resolves problems with the driver's return stroke.
Covers weak drive, broken drivers, poor feed, and tool jamming.
Guidance for unresolved problems, directing users to contact Senco.
Outlines warranty coverage, conditions for honoring, and exclusions.
Details the process for replacing tools lost to natural disasters.
General| Power Source | Pneumatic |
|---|---|
| Magazine Capacity | 300 |
| Operating Pressure | 70 to 120 PSI |
| Length | 12.5" |
| Tool Weight | 5.1 lbs (2.3 kg) |
