To Next PageTo Next Page
Need help?Do you have a question about the Senco SLP20 and is the answer not in the manual?
Adjusting the magazine height lever for LS1, LS2, and LS5 models.
Loading fasteners and opening the magazine rail for FinishPro 10.
Using the secondary and primary triggers for the FinishPro 10.
Loading fasteners into the magazine for various SENCO models.
Using the safety element against the workpiece on the FinishPro 25XP.
Adjusting tool power output using the integrated power adjustment system.
Adjusting fastener depth using the depth control safety element.
Adjusting the direction of the exhaust air on the FinishPro 25XP.
Reminder to read and understand the SAFETY INSTRUCTIONS manual before use.
Ensuring screws are tight and performing daily safety inspections.
Information on routine lubrication for SLP20 and FinishPro 25XP.
Correct application of Senco pneumatic oil for tool maintenance.
Daily cleaning, inspection, and use of non-flammable cleaning solutions.
Listing of available accessories for SENCO tools.
Information on kits to convert LS tools for different fastener sizes.
Guidelines for repairs and important safety warnings for tool use.
Troubleshooting air leaks near the top of the tool and sluggish operation.
Troubleshooting air leaks near the bottom of the tool and poor return.
Addressing issues with broken drivers, weak impulse, and feed jamming.
Specifications for minimum/maximum operating pressure and air consumption.
Details on tool dimensions and fastener capacity per magazine.
Codes and sizes for fasteners used with FinishPro 15/18, 25XP, and SLP20 models.
Codes and sizes for fasteners used with LS1 and LS2 models.
Codes and sizes for fasteners used with the FinishPro 10 model.
Codes and sizes for fasteners used with the FinishPro 2N1 model.
Details on the warranty period and coverage for SENCO tools and parts.
Conditions required for warranty claims, including proper use and proof of purchase.
Exclusions and limitations of liability for SENCO tool warranties.
Procedure for tool replacement following destruction by natural disaster.
Adjusting the magazine height lever for LS1, LS2, and LS5 models.
Loading fasteners and opening the magazine rail for FinishPro 10.
Using the secondary and primary triggers for the FinishPro 10.
Loading fasteners into the magazine for various SENCO models.
Using the safety element against the workpiece on the FinishPro 25XP.
Adjusting tool power output using the integrated power adjustment system.
Adjusting fastener depth using the depth control safety element.
Adjusting the direction of the exhaust air on the FinishPro 25XP.
Reminder to read and understand the SAFETY INSTRUCTIONS manual before use.
Ensuring screws are tight and performing daily safety inspections.
Information on routine lubrication for SLP20 and FinishPro 25XP.
Correct application of Senco pneumatic oil for tool maintenance.
Daily cleaning, inspection, and use of non-flammable cleaning solutions.
Listing of available accessories for SENCO tools.
Information on kits to convert LS tools for different fastener sizes.
Guidelines for repairs and important safety warnings for tool use.
Troubleshooting air leaks near the top of the tool and sluggish operation.
Troubleshooting air leaks near the bottom of the tool and poor return.
Addressing issues with broken drivers, weak impulse, and feed jamming.
Specifications for minimum/maximum operating pressure and air consumption.
Details on tool dimensions and fastener capacity per magazine.
Codes and sizes for fasteners used with FinishPro 15/18, 25XP, and SLP20 models.
Codes and sizes for fasteners used with LS1 and LS2 models.
Codes and sizes for fasteners used with the FinishPro 10 model.
Codes and sizes for fasteners used with the FinishPro 2N1 model.
Details on the warranty period and coverage for SENCO tools and parts.
Conditions required for warranty claims, including proper use and proof of purchase.
Exclusions and limitations of liability for SENCO tool warranties.
Procedure for tool replacement following destruction by natural disaster.
General| Magazine Capacity | 110 |
|---|---|
| Operating Pressure | 70-120 psi |
| Air Inlet | 1/4" NPT |
| Fastener Type | 18 Gauge Brad Nails |
| Fastener Range | 5/8" to 1-5/8" |
| Height | 9.5" |
