EasyManua.ls Logo

Sencor SBP 901 - Using the Blood Pressure Monitor; Selecting a Power Source; Setting Date, Time, and Units

Sencor SBP 901
14 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Digital
Blood
Pressure
Monitor
with
Cuff
SBP
901
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
Important:
If
the
polarity
is
reversed
when
the
batteries
are
inserted,
the
device
may
not
only
not
function
but
may
also
heat
up.
Do
not
combine
used
and
new
batteries
or
batteries
of
various
types,
e.g.
alkaline
batteries
and
rechargeable
batteries.
Note:
Do
not
use
the
adapter
and
batteries
at
the
same
time.
Setting
the
date,
time
and
measuring
units
Before
taking
measurements,
set
the
current
date,
time
and
measuring
unit.
The
measured
values
will
be
stored
in
memory
together
with
the
date
and
time
of
measurement.
Check
that
the
device
is
turned
off
(the
LCD
display
is
off)
or
turn
it
off
using
the
START/STOP
button.
Hold
down
the
SET
У
sensor
with
your
finger
for
З
seconds.
During
the
initial
setup
the
display
will
show
year
(2000),
month
(1)
and
day
(1).
The
year
(2000)
will
flash
on
the
display.
Set
the
current
year
using
the
А
MEM
touch
sensor.
Confirm
the
setting
by
touching
the
SET
Y
sensor.
The
device
will
automatically
switch
to
the
month
setting
mode.
Set
the
current
month
using
the
A
MEM
touch
sensor.
Confirm
the
setting
by
touching
the
SET
Y
sensor.
The
device
will
automatically
switch
to
the
day
setting
mode.
Set
the
current
day
of
the
month
using
the
A
MEM
touch
sensor.
Confirm
the
setting
by
touching
the
SET
W
sensor.
The
device
will
automatically
switch
to
the
hour
setting
mode.
Set
the
current
hour
using
the
А
MEM
touch
sensor.
Confirm
the
setting
by
touching
the
SET
Y
sensor.
The
device
will
automatically
switch
to
the
minute
setting
mode.
Set
the
current
minute
using
the
А
MEM
touch
sensor.
Confirm
the
setting
by
touching
the
SET
Y
sensor.
The
device
will
automatically
switch
to
the
measuring
unit
selection
mode.
Select
the
measuring
unit
mmHg
or
kPa
using
the
A
MEM
sensor.
Confirm
the
setting
by
touching
the
SET
У
sensor.
Note:
The
standard
measuring
unit
for
the
measurement
of
blood
pressure
is
mmHg
(millimetres
of
a
mercury
column).
After
completing
the
setup,
"done"
will
appear
on
the
display.
Setup
of
the
date,
time
and
meas-
uring
units
is
complete.
Then
the
device
will
turns
itself
off
automatically.
Note:
Setting
range:
year
2000-2050,
time
format:
24
hour
Measurement
Basic
instructions
for
achieving
the
most
accurate
measuring
results
Always
take
measurements
at
the
same
time
of
day,
ideally
in
the
morning,
at
noon
and
in
the
evening
under
the
same
conditions
or
according
to
the
recommendations
of
your
doctor.
Do
not
perform
measurement
sooner
than
30-45
minutes
after
consuming
coffee,
tea
or
smoking
a
cigarette.
Wait
at
least
20
minutes
after
taking
a
hot
shower
or
bath.
During
measurement
sit
calmly,
relaxed
and
don't
talk.
Do
not
move
the
arm
to
which
the
cuff
is
attached.
Wait
approximately
4-5
minutes
before
measuring
again.
Copyright
©
2011,
Fast
CR,
a.s.
Revision
03/2011

Related product manuals