EasyManua.ls Logo

SEON TR4-20 - User Manual

Default Icon
2 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Camera 1
harness
Alarm switch
Fuse holder
Connectors
DVR
(rear view)
Speed harness
Signal harness
Optional external
audio input for camera 1
Power and ignition harness
Alarm harness
Cable retainers
To camera 1
Battery + (red)
Battery (black)
Ignition switch (yellow)
Left turn signal, indicator 1 (black)
Stop arm, indicator 2 (green)
Brakes, indicator 3 (red)
Warning lights, indicator 4 (brown)
Right turn signal, indicator 5 (white)
Speed sensor ground (black)
Speed pulse signal (green)
Speed sensor power 7.5 (red)
VDC
Wiring and Testing
1
Feed all of the through the cable grommet and connect them to
the DVR as shown below.
harnesses
2
Make sure all cables are held inside the cable retainers at the back of the
DVR, as shown below. Carefully slide the DVR into the enclosure, taking care
not to pinch or bind any cables. Slide the lid onto the enclosure and secure it
with two #8×¼" retaining screws.
3
Connect all of the harnesses as shown above. Turn on the ignition switch. If
the light on the front of the DVR does not turn green within
POWER 30 seconds,
read the troubleshooting instructions in the .Installation and User's Guide
4
Follow the DVR setup instructions in the or
the
Quick Reference Guide
Installation and User's Guide.
IMPORTANT: The DVR must be connected as close to the battery
(or master battery switch) as possible to avoid a low-voltage DVR
shutdown when the battery is heavily loaded.
Information in this guide is subject to change without prior notice.
© 2004 Seon Design Inc. www.seon.com
All rights reserved. Document Part Number: 700-0031-01
TR4-20 Full-Featured Mobile DVR System
Quick Installation Guide
If your TR4-20 Full-Featured Mobile DVR System is to be returned to Seon Design for service, please
call toll free 877-630-7366, or 604-524-6437 and ask for a Return Authorization (RA) number. An RA
number allows the Service Technicians to better track your product when it comes in for service. Please
show the RA number on the outside of the package. ANY PRODUCT SENT TO SEON DESIGN
WITHOUT AN RA NUMBER MAY BE REFUSED.
Please refer to the Warranty form provided with your product to review the terms of warranty service,
contact and shipping information, as well as other important issues regarding the service and operation
of your product.
Service and Warranty
Question and Answer IconNeed help?

Do you have a question about the SEON TR4-20 and is the answer not in the manual?

Summary

Wiring and Testing

Connect Harnesses

Feed all harnesses through the cable grommet and connect them to the DVR.

Secure Cables and DVR

Ensure cables are in retainers, slide DVR into enclosure, and secure lid with screws.

Battery Connection

Connect DVR close to the battery to avoid low-voltage shutdown during heavy load.

Initial Power On

Connect harnesses, turn on ignition, and check POWER light; consult troubleshooting if needed.

Service and Warranty

Disassembly

Unlock and Remove Door

Use the flat key to unlock and remove the enclosure door.

Remove Enclosure Lid

Use a Phillips screwdriver to remove screws and take off the enclosure lid.

Remove DVR from Enclosure

Pull tabs on the DVR sides to slide it out of the enclosure.

Mounting

Cable Grommet and Hole Plug Adjustment

Swap cable grommet and hole plug for power and camera cables if needed.

Mounting Enclosure

Use screws to mount the enclosure horizontally or vertically as shown.

SEON TR4-20 Specifications

General IconGeneral
Hard Drive CapacityUp to 6TB
Video CompressionH.264
Motion DetectionYes
Operating SystemEmbedded Linux
Video Input4 channels
Hard Drive Support1 SATA HDD
Audio Output1 channel
Network InterfaceRJ45, 10/100 Mbps
USB Interface2 x USB 2.0

Related product manuals