4. Sleep
Time Setting
Long
press
K2key, enter
the setting
item, and
then continue
to short
press
K2
key to
traverse
the setting
item, enter
the sleep
time setting
item
(Note'
after entering
the
sleep time
setting
item,
the LED screen
value displays
the
value, without
celsius,
Fahrenheit
symbol display),
Short
press
Kl key to enter
the setting, short
press
K1
key to set the
time of entering
sleep
-1
minute,
long
press
Kl key to
set the sleep
time lo decrease
continuously during
key
press;
short
press
K2 key
to enter sleep
+'1
minute, long
press
K2
key to set
the sleep
time
to increase
continuously
during key
press.
When
the
preset
value
is reached,
release the
key. Press
the Kl
and
K2 keys at
the same
time to
save the settings
and
exit the settings.
nfrfr
e
[]trlfJ'p
lll. Heating
Function
1. ln the idle state:
Long
press
Kl
key, release
the key, start
to heat
up. After
warming up
to the target
setting
value,
the target
setting
temperature
will be
maintained.
2.
ln the temperature
control
state:
a. Long
press
Kl
key to continuously
decrease
the
target
temperature,
and long
press
K2 key
to
continuously
increase
the target
temperature.
When
the key is
released, the
temperature
will drop,/rise
to the target
value.
b. Press
K1 and K2
keys ai the same
time
to enter
ihe function setting
(the
setting
method
the same
as above).
After the
data setting
is
completed,
release the
key and
wait for the
setting
to be
saved automatically
and exit.
lV. Sleep
And
Wake Up
'1.
After reaching
the
set sleep
time, it
will enter
the sleep state.
At
this time,the
temperature
is IOO
"C,
and
within
5 minutes
during
the sleep
period,
press
the
Kl
and
K2
keys at the
same
time to
enter the setting
item and
wake up the
device. Or
pick
up the
shaking sold-
ering
iron again
to wake
up.
lf there is
no required setting
item at
this time,
the device
will
return
to the
previous
state
after
waiting
for the setting
item to
exit.
2. lf there
is no
wake-up within
5 minutes
after
the start of
sleep,then
after
5 minutes and
entering
the deep
sleep state,
you
will not
be able to
wake up from
sleep
at this
time,
you
can
only
press
the
K3 key to
restart the
device.
3. When
entering
deep sleep
state,
only the
temperature
unit
light is on under
normal state,
and
other
LED indicators
are
not on.
V. Fault
Detection
1. Turn
on
without
power
and check
whether
the socket
is
plugged
or
not.
2. After turning
on,
if the LED displays
"H-E",
it meets that the
temperature
sensor
has been
on,
the
heater fault and
the
heater
should be
replaced.
Vl.Factory
Default Settings
Temperature
unit
C
Factory temperature
300
'c
Compensation
temperature
o"c
Sleep time
10 min
Sleep temperature
100
'c
Deep sleep
Sleep
for 5 minutes
without
waking up, enter
deep sleep,
press
K3 to restart
*
After setting status
timeout,
the current
seuing
will be
saved automatically
and
exit. Compensa:ion
temperature
setting
range:
-5O
to
+5o
'C.
*
After.setting
glatus
tirneou!,rthe.currell:gqlti.ng:'illl
be'Saygddu1omq.licql.li,r
and
exk.s,leeptime,sgtiirrg'rbrige,,t.id,'*iihule5.;.,:''--''1"'lr.iii":'.11
-',1:
To Next Page
Loading...