DAL 1965
Page 5/12
DEFINITION OF THE CLAMPS
CLAMPS
CONNECTIONS
DESCRIPTION
23 - 24
NETWORK
POWER SUPPLY
230Vac ±10% 50/60 Hz power supply input, which via fuse F4 powers the primary of the
toroidal transformer - already wired -
13 - 14
FLASHING
17 - 18
MOTOR M1
Motor M1 24Vdc power supply output for single wing or pedestrian wing (to which electric lock
can be connected), delayed closure.
9 - 10
PHOTOCELLS
POWER SUPPLY
Power supply output 24Vdc (9 = -, 10 = +) max 500mA for accessories such as photocells
6
OPENING
PHOTOCELL
5
CLOSURE
PHOTOCELL
1
4
PEDESTRIAN
CONTROL
STOP KEY
Stop control input (NC contact). When pressed it blocks functioning of the motors, if pressed
during the open gate pause time it annuls automatic closure.
2
START
COMMAND
Start control input (NO contact), controls the opening and closure in step-by-step mode.
N.B. This function can be modified as described in "modify controls".
Photocell input active in opening and closing (NC contact).
If blacked-out in the opening phase, the gate stops, re-starts opening as soon as the photocell
is no longer engaged.
If blacked-out in the closure phase, the gate stops, re-opens as soon as the photocell is no
longer engaged.
Photocell input active only in closing (NC contact). If blacked-out in the closure phase, the
gate stops and then re-opens.
COMMON
INPUTS
Inputs common clamps
11 - 12
CONTROL FOR
ELECTRIC LOCK
OR GATE OPEN
INDICATOR LIGHT
33 - 34
RECEIVER
ANTENNA
INCORPORATED
Flashing light power supply output (24Vdc-max 25W) to be used with flashing light without -
SERAI RZ/24F- internal electronics. Flashing is fast during closure, slow during opening and
very slow when functioning with battery.
8
3 - 7
24Vdc output (11 = -, 12 = +) with the following functioning:
With SW2dip2 OFF: impulse control for electric lock -SERAI M/83/1-.
With SW2dip2 ON: control with the gate open indicator light function
Input for the connection of the antenna for the built-in receiver.
(33=BRAIDING/EARTH, 34=ANTENNA)
Sensitive edge input (NC contact), inverts movement by 10cm.
SENSITIVE
EDGE
LEDS INDICATION
LED
DL5=PH OP
DL4=PHOTO
DL3=STOP
DL1=PED
DL2=START
ON OFF
FUNCTION
Internal photocell
External photocell
Stop button
PEDESTRIAN button
Open/Close button
Opening photocell free from
obstacles
Closure photocell free from
obstacles
Stop button in normal state
Pedestrian button pressed
Open/Close button pressed
Opening Photocell blocked out
(presence of an obstacle)
Closure Photocell blocked out
(presence of an obstacle)
Stop button pressed
Pedestrian button in normal state
Open/close button in normal state
DL6
Programming
Indicates the various phases of the programming
DL7=COSTA
Sensitive edge
Sensitive edge in normal state Sensitive edge pressed
ATTENTION: this voltage is not present in battery functioning with
gate at a standstill.
15 - 16
AUXILIARY
POWER SUPPLY
Power supply output 24Vdc (15 = +, 16 = -) max 200mA for accessories that must always be
powered, for example external radio receivers.
19 - 20
MOTOR M2
M2 motor 24Vdc power supply output for delayed wing opening
21 - 22
TRANSFORMER
SECONDARY
INPUT
20Vac input for power supply of the circuit board supplied via a toroidal transformer- already
wired-
27 - 28
OPTIONAL
BATTERIES
Input for the connection of N°2 12V 2Ah buffer batteries (optionals, e.g. SERAI BT/15 or
BT/20) to guarantee functioning of the automation in the case of a power cut. In presence of
the circuit board network voltage, it recharges the batteries via the built-in battery-charger
CR/41/24 I E
Pedestrian control input (NO contact). With DIP1 SW1 OFF only the wing connected to M1
opens. With DIP1 SW1 ON the single wing opens (M1) for 7s.
N.B. This function can be modified as described in "modify controls".
To Next Page
Loading...
Need help?
General