Serai KIT/39 F - User Manual

Page 1/18
KIT/30-39F I E
!
Thank you for choosing a SERAI ELETTRONICA product, which we are confident will perform to your requirements.
Please be advised that you are about to fit a system classified as “a power-operated drive designed to move automatic ga-
tes and doors in commercial or residential buildings accessed by vehicles and persons”, and as such, the system must be
considered potentially hazardous. By law, you are responsible for rendering this equipment as “safe” as is reasonably pos-
sible.
Installation and maintenance of equipment of this kind must therefore be carried out by skilled, qualified and trained
personnel, working in a professional manner, as provided for by law n. 37/08 and any subsequent amendments and
supplements. The law in question prohibits the construction of these types of systems by non-qualified personnel.
SERAI manufacturing complies with the following legislation:
Applicable directives for the CE marking :
Machines: 2006/42/EC
Low Voltage: 2006/95/EEC
Electromagnetic Compatibility: 2004/108/EEC
General applicable standards:
Electrical Safety: IEC EN60335-1 + IEC EN60335-2-103
Electromagnetic Compatibility - Emissions: CEI EN61000-6-3
Electromagnetic Compatibility - Immunity: CEI EN61000-6-
Apart from the legislation mentioned above, you are also reminded to comply with the following standards during the
installation phase.
General applicable standards:
Safety of electrical systems in non-specialised environments: CEI 64-8 V2
Specific product standards applicable:
Safety in the use of power-operated doors - requirements: UNI EN12453
Safety in the use of power-operated doors - testing methods: UNI EN12445
SERAI products enable users to build systems which comply with these standards. This is extremely important as
THE INSTALLER IS LIABLE FOR THE SYSTEM AND FOR ENSURING ITS OPERATION COMPLIES WITH
LEGAL PROVISIONS.
This handbook must be read in full before proceeding with the installation of the various parts of the system.
The installation of the mechanical end stops for gate opening and closure is necessary for system safety purposes
and therefore this operation must be performed before proceeding with the installation of the control unit.
SINCE 1965
E R A IS
GATE AUTOMATION DIVISION
INSTALLATION MANUAL
KIT/30 F - SR 03.32 F - KIT WITH 2 MOTORS FOR SWING GATES UP TO 3.0 + 3.0 METERS AND
300 kg PER LEAF - 230 Vac
KIT/39 F - SR 02.39 F - KIT WITH 2 MOTORS FOR SWING GATES UP TO 2.0 + 2.0 METERS AND
200 kg PER LEAF - 230 Vac

Summary

Gearmotor Technical Specifications

Final Installation Procedures

Moving the Gate Manually in Event of Power Failure

Explains how to operate the gate manually during a power outage using the release lever.

CR;41 Control Unit Installation

Control Unit Positioning

Wiring Diagram and Control Unit Interface

Terminal Connections and Descriptions

Details terminal connections, their functions, and descriptions for the control unit.

Control Unit Buttons and Functions

Explains the functions of buttons (SET, BREAK, WORK) and the POWER potentiometer.

Motor Force Adjustment and Connections

Electric Connections of Motor

Guides on connecting motors to the electronic control unit, specifying wire colors and terminals.

Earth Connection Between Motor and Home System

Microswitch Settings for Gate Operation

Gate Configuration and Deceleration Settings

Details microswitch settings for gate configuration, deceleration speed, final closure, electric lock release, and start-up torque.

Gate Movement Commands and LED Signals

Command Sent During Gate Movement

Input of Opening Photocell or Sensitive Edge

LED Functions

Control Unit Programming

Two-Leaf Gate Work and Deceleration Time Programming

Step-by-step guide to program work and deceleration times for two-leaf gates using DIP1 SW1 OFF.

Gate Open Pause and Programming

Single Leaf Gate Work and Deceleration Time Programming

Step-by-step guide to program work and deceleration times for single leaf gates using DIP1 SW1 ON.

Automatic Reclosure Programming

Instructions for activating and deactivating the automatic reclosure function and setting the pause time.

Radio Control Code Learning Procedures

Microswitch Configuration for Mini Transmitters

Start and Pedestrian Code Learning

Step-by-step process for learning start and pedestrian control codes from mini transmitters.

Erasure of Stored Radio Codes

CR;41 Control Unit Technical Specifications

P;10 Photocell Installation and Specifications

Photocell Dimensions, Positioning, and Alignment

Photocell Connections and Technical Specifications

Troubleshooting Guide

Gearmotor Not Working or Gate Not Completing Travel

Lists causes and solutions for gearmotor malfunctions and incomplete gate travel.

Gate Slow Start-up and Remote Control Range Issues

Addresses problems with slow gate start-up, problematic start-up, and reduced remote control range.

Serai KIT/39 F Specifications

General

Brand	Serai
Model	KIT/39 F
Category	Gate Opener
Language	English