Sharp AR-M258

AR-M256/M257/M258/M316/M317/M318/5625/5631 TROUBLE CODE LIST 9 - 4
F1 00 Content Finisher communication trouble
Details Communication line test error occurs when
power is turned on or after the exit of a
simulation mode.
Error in finisher communication
Cause Connection trouble or disconnection of the
connector and harness between the body
and the finisher.
Finisher control PWB trouble.
Control PWB failure.
Malfunction by noises.
Check
and
remedy
Canceled by turning OFF/ON the power.
Check the connectors and the harness of
communication line.
Replace the finisher control PWB.
01 Content Side guide plated home position error
(AR-FN5A)
Details The side guide plate cannot return to the
posittion of home position error.
Cause Side guide plate drive motor abnormality.
Side guide plate home position sensor
abnormality.
Finisher PWB abnormality.
Check
and
remedy
Use SIM3-3-1 to check the side guide
plate motor operation.
03 Content Paddle motor trouble (AR-F14N)
Details Paddle motor operation abnormality
Cause Motor lock.
Motor rpm abnormality.
Overcurrent to the motor.
Finisher control PWB trouble.
Check
and
remedy
Use SIM3-3-10 to check the paddle motor
operation
06 Content Offset motor trouble (AR-FN5A)
Slide motor trouble (AR-F14N)
Details (AR-FN5A) When the offset motor of the
finisher is driven it does not reach the
specified position.
(AR-F14N) Slide motor operation
abnormality
Cause (AR-FN5A)
Offset motor abnormality.
Offset motor origin sensor abnormality.
Finisher PWB abnormality.
(AR-FN14N)
Motor lock.
Motor rpm abnormality.
Overcurrent to the motor.
Finisher control PWB trouble.
Check
and
remedy
(AR-FN5A)
Use SIM 3-3-6 to check the offset motor
operation
(AR-F14N)
Use SIM 3-3-6 to check the slide motor
operation
Trouble
code
Details of trouble
Main
code
Sub
code
F1 08 Content Staple motor error (AR-FN5A)
Details The staple motor cannot return to the
home position
Cause Staple motor abnormality.
Staple motor home position sensor
abnormality.
Staple unit abnormality.
Finisher PWB abnormality.
Check
and
remedy
Use SIM 3-3-7 to check the staple motor
operation
10 Content Staple motor trouble (AR-F14N)
Details Staple motor operation abnormality
Cause Motor lock.
Motor rpm abnormality.
Overcurrent to the motor.
Finisher control PWB trouble.
Check
and
remedy
Use SIM 3-3-5 to check the staple motor
operation.
11 Content Rear edge plate home position error
(AR-FN5A)
Bundle exit motor trouble (AR-F14N)
Details (AR-FN5A) The rear edge plate cannot
return to the home position
(AR-F14N) Bundle exit motor operation
abnormality
Cause (AR-FN5A)
Rear edge plate drive motor abnormality.
Side guide plate home position sensor
abnormality.
Finisher PWB abnormality.
(AR-F14N)
Motor lock.
Motor rpm abnormality.
Overcurrent to the motor.
Finisher control PWB trouble.
Check
and
remedy
(AR-FN5A) Use SIM 3-3-2 to check the
rear edge plate motor operation
(AR-F14N) Use SIM 3-3-9 to check the
bundle exit motor operation
15 Content Finisher lift-up motor trouble
Details The finisher lift-up motor does not reach
the specified position
Cause Lift-up motor abnormality.
Lift-up motor upper limit sensor
abnormality.
Finisher PWB abnormality.
Check
and
remedy
Use SIM 3-3-5 to check the lift-up motor
operation
19 Content Alignment motor (F) trouble (AR-F14N)
Details Alignment motor operation abnormality
Cause Motor lock.
Motor rpm abnormality.
Overcurrent to the motor.
Finisher control PWB trouble.
Check
and
remedy
Use SIM3-3-8 to check the alignment (F)
motor operation.
Trouble
code
Details of trouble
Main
code
Sub
code