CD-C606/1900,CP-C606/1900
– 5 –
OPERATION MANUAL
AM 0:00AM 12:00 0:00
(Main unit operation)
In this example, the clock is set for the 12-hour
(AM 12:00) system.
2
3
5
6
7
9
POWER
MEMORY/
SET
CLOCK
TUNING/
TIME
( )
1
Press the POWER button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Press the TUNING/TIME ( or ) button to select the time
display mode.
"AM 12:00" The 12-hour display will appear.
(AM 12:00 - PM 11:59)
"AM 0:00" The 12-hour display will appear.
(AM 0:00 - PM 11:59)
"0:00" The 24-hour display will appear.
(0:00 - 23:59)
Note that this can only be set when the unit is first installed or
it has been reset (see page 13).
5
Press the MEMORY/SET button.
6
Press the TUNING/TIME ( or ) button to adjust the hour.
Press the TUNING/TIME ( or ) button once to advance
the time by 1 hour. Hold it down to advance continuously.
When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
7
Press the MEMORY/SET button.
8
Press the TUNING/TIME ( or ) button to adjust the minutes.
Press the TUNING/TIME ( or ) button once to advance
the time by 1 minute. Hold it down to change the time in 5
minute intervals.
The hour setting will not advance even if minutes advance
from "59" to "00".
9
Press the MEMORY/SET button.
The clock starts operating from "0" seconds. (Seconds are not
displayed.)
Note:
In the event of power failure or when the AC power cord is
disconnected, the clock display will go out.
When the AC power supply is restored, the clock display will
flash on and off to indicate the time when the power failure
occurred or when the AC power cord was disconnected.
If this happens, follow the procedure below to change the clock
time.
To change the clock time:
Press the CLOCK button.
Within 5 seconds, press the MEMORY/SET button.
Perform steps 6 - 9 above.
To see the time display:
Press the CLOCK button.
The time display will appear for about 5 seconds.
To change the time display mode:
Perform steps 1 - 2 in the section "RESETTING THE MICRO
COMPUTER".
Perform steps 1 - 9 above.
SETTING THE CLOCK
8
4
1
2
3
1
2
PREPARATION FOR USE
Remote control
Notes concerning use:
Replace the batteries if the operating distance is reduced or if
the operation becomes erratic.
Periodically clean the transmitter LED on the remote
control and the sensor on the main unit with a soft cloth.
Exposing the sensor on the main unit to strong light may inter-
fere with operation. Change the lighting or the direction of the
unit.
Keep the remote control away from moisture, excessive heat,
shock, and vibrations.
15
15
15
1
8" - 20'
(0.2 m - 6 m)
■
●
●
●
●
RESETTING THE MICROCOMPUTER
Reset the microcomputer under the following conditions:
To erase all of the stored memory contents (clock and timer
settings, and tuner and CD presets).
If the display is not correct.
If the operation is not correct.
1
Press the POWER button to enter the stand-by mode.
2
Press and hold down the / button and the /
button, hold down the POWER button for at least 1 second.
Caution:
The operation explained above will erase all data stored in
memory including clock and timer settings, and tuner and CD
preset.
1,2
2
●
●
●
●
To Next Page
Loading...
Need help?
General
