Sharp CD-PC651H

Hi
Dolby
Pro
Logic
Surround
mode
Video
and
Laser
Disc
sofiware
programmes
carrying
the
DiC
eotey
sunrauno|trademark
are
recordings
that
contain
the
same
Dolby
Surround
data
as
used
in
movie
theatres.
The
Dolby
Pro
Logic
Surround
mode
uses
Dolby
Surround
data
to
bring
the
full
presence
experienced
in
a
movie
theatre
into
your
home.
To
use
this
mode,
you
must
connect
the
surround
and
centre
channel
speakers.
Before
playing
a
video
{or
Laser
Disc)
software
programme
car-
rying
the
[[[potev
sunrouno)
trademark,
be
sure
to
complete
the
“Dolby
Pro
Logic
Surround
setup"
as
follows.
Dolby
Pro
Logic
Surround
setup:
(Remote
control
operation)
1
Press
the
ON/STAND-BY
button
to
turn
the
power
on.
2
press
the
DOLBY
PRO
LOGIC
button.
@
The
NORMAL
or
PHANTOM
button
will
fight.
3
Select
the
centre
mode
using
the
CENTER
MODE
button.
NORMAL:
The
centre
speaker
is
used.
PHANTOM:
Use
this
mode
when
a
centre
speaker
is
not
connected.
The
centre
channel
signals
are
output
through
the
front
speakers.
@
The
selected
centre
mode
is
automatically
stored
in
memory
and
will
be
used
the
next
time
you
activate
DOLBY
PRO
LOGIC or until it is changed.
4 press the TEST TONE button.
@
The
test
tone
is
a
tone
that
moves
from
one
speaker
to
ihe
next,
taking
2
seconds
to
go
from
speaker
to
speaker.
In
NORMAL
mode:
In
PHANTOM
mode:
Left
(L
ch)
Left
(L
ch)
{
eae
{C
ch)
Right
(R
ch)
}
Right
{R
ch}
Surround
(S
ch)
Sainsiaa (S ch)
5
Adjust
the
centre
speaker
volume
or
the
volume
of
the
sur-
round
speakers.
To
adjust
the
centre
speaker
volume
to
match
the
level
of
the
front
speakers:
Press
the
CENTER
LEVEL
A
button
to
increase
the
volume
and
the
CENTER
LEVEL
vy
button
to
decrease
the
volume.
To
adjust
the
volume
of
the
surround
speakers
to
match
the
level
of
the
front
speakers:
Press
the
SURROUND
LEVEL
A
button
to
increase
the
volume
and
the
SURROUND
LEVEL
vy
bution
to
decrease
the
volume.
6
apes
adjusting
the
speaker
volume,
press
the
TEST
TONE
utton.
@
The
test
tone
will
stop.
Notes:
@
Be
sure
to
adjust
the
sound
from
your
favorite
listening
position.
@
The
volume
is
adjusted
in
1
dB
steps
up
or
down
each
time
you
press
the
CENTER
LEVEL.
button
or
the
SURROUND
LEVEL
button.
@
The
volume
settings
for
ihe
centre
and
surround
speakers
are
stored
in
memory
for
future
use.
However,
if
the
power
is
dis-
connected
or
there
is
a
power
failure,
the
!evels
will
return
to
their
initial
settings.
E-12
Front
Froni
speaker
speaker
(Left)
(Right)
Surround
Surround
speaker
speaker
(Left)
(Right)
DOLBY
CENTER
PRO
LOGIC
LEVEL
«™
NZ
CENTER
SURROUND
MODE
LEVEL
“I~
TEST
TONE
ON/
STAND-BY
Dolby Pro Logic Surround playback:
1 Press the NORMAL or PHANTOM button on the
main unit or the DOLBY PRO LOGIC button on the
remote control.
@ The NORMAL or PHANTOM button will illuminate,
and the unit will enter the Dolby Pro Logic Surround
mode.
2 Select the centre mode using the CENTER MODE
button.
NORMAL: The centre speaker is used.
PHANTOM: Use this mode when a centre speaker
is not connected. The centre channel
signals are output through the
front speakers.
3 Play the video software programme.
4 To cancel the Dolby Pro Logic Surround mode, press
the BYPASS button on the main unit or the DOLBY
PRO LOGIC button on the remote control.
@ The BYPASS bution wil! light.
Notes:
@ You cannot use the Dolby Pro Logic Surround feature —
with headphones.
@ If you use headphones, cancel the Dolby Pro Logic
Surround mode.
Even after the headphones are connected, if the unit
is in the Dolby Pro Logic Surround mode, sound will
still be heard from the surround and centre speakers.