30
General I would like to have louder
sound by connecting additional
speakers. For TV models with
digital optical audio output.
1) Use the 3.5mm headphone output and a 3.5mm to phono cable (available
separately) to connect to an amplifi er/surround sound system. Please note this
will deactivate the TV’s built in speakers.
2) Connect a digital optical audio cable from the TV’s digital optical audio output
to your amplifi er/surround systems digital optical audio input.
General Why are some options in the menu
unavailable and greyed out.
Some options are only available in certain sources, i.e. HDMI. They are
unavailable in the other sources where they have no a ect.
General Can I stop my TV automatically
turning o after 4hrs?
Yes, in the ‘Time’ menu settings, scroll down to Auto standby and select OFF.
TV I have tuned in Digital TV but I
am not receiving any or all of the
channels and/or the channels I
receive are breaking up.
1) Check you are in an area that can receive Freeview/Saorview, visit www.freeview.co.uk or
www.saorview.ie
2) Check you are using an aerial that is able to receive a good digital signal. In most cases,
you will need an outdoor digital hi-gain/wideband aerial. In areas that have excellent
digital coverage, you may be able to use a loft type aerial but it is highly likely that you will
also need to connect a booster between the back of the TV and the TV aerial wall socket.
Unfortunately, to receive a good enough digital signal, it is not possible to use a portable/
indoor type aerial.
TV I have re-tuned my television but
when I switch it o it is not storing
the channels.
If the TV does not save the channels when you power it o , it’s likely the channel database
has become corrupt.
1) Turn o the TV.
2) Remove the RF/Aerial cable from the rear of the TV and then turn the TV back on again.
3) Using the remote control, press Menu followed by 8-8-8-8 to enter the initial setup/ rst
time installation menu.
4) Press OK (let the TV run the full tuning process).
5) Once completed, turn o the TV, reconnect the RF/Aerial cable then turn the TV back on
again.
6) Repeat steps 3 & 4.
VCR/DVD
Recorder
I have connected the TV to my VCR
or DVD Recorder via SCART but it is
not recording.
In addition to connecting via SCART, you should connect the aerial cable from the wall
socket to your VCR/DVD Recorder and another aerial cable from the VCR/DVD Recorder to
the TV.
Game Consoles I have connected my Playstation/
Xbox to the TV via HDMI, but I am
not receiving any pictures or sound
on my TV
1) Ensure the TVs’ source is set to HDMI.
2) Check your settings on your Playstation/Xbox are as per the Playstation/Xbox
instruction manual.
Game Consoles I have connected my Playstation/
Xbox to the TV via Component
cables (red, green & blue) but I am
not receiving any sound.
Component cables only provide HD pictures. For the sound you will need to connect the
red & white audio cables on the Playstation/Xbox to the red & white phono inputs (or mini
AV input where tted) on the rear of the TV. Please refer to the ‘Connections’ pages.
System Lock I have changed the password
on the television and now
forgotten it.
There is a master password of 4711, to gain access to the TV menu and reset the
normal password.
Freeview HD I cannot access all Freeview
channels.
Some data channels for Freeview can only be obtained when the TV ‘s ethernet port is
connected to your router.
Freeview HD I cannot nd the Freeview HD
channels.
Freeview HD channels found during tuning will be placed in channel positions above 100.
For example, 101 (BBC1 HD), 102 (BBC2 HD) etc.
FREQUENTLY ASKED QUESTIONS
General Information
Sharp - User Guide - LC-24DHE4011K - SHA-MAN-0144.indd Sec1:30Sharp - User Guide - LC-24DHE4011K - SHA-MAN-0144.indd Sec1:30 09/05/2016 16:39:1009/05/2016 16:39:10
To Next Page
Loading...
