Sharp MD-MS701H - Page 18

MD-MS701H/MS702H
– 18 –
: RF side focus gain minor adjustment  : Gain setting
: A-ATT (focus) initial setting  : ATT setting : B-ATT (focus) initial setting  : ATT setting : S gain "High" A signal offset (AINO) measurement  : Measurement value
: S gain "High" B signal offset (BINO) measurement  : Measurement value
: S gain "High" E signal offset (EINO) measurement  : Measurement value : S gain "High" F signal offset (FINO) measurement  : Measurement value TCRS signal offset (TCRSO) measurement  : ATT setting : S gain "Low" A signal offset (AINO) measurement  : Measurement value : S gain "Low" B signal offset (BINO) measurement  : Measurement value : S gain "Low" E signal offset (EINO) measurement  : Measurement value
: S gain "Low" F signal offset (FINO) measurement  : Measurement value
Continued from the preceding page
R F G
SKIP UP SKIP DOWN
S A
SKIP UP SKIP DOWN
S B
SKIP UP SKIP DOWN
A H
SKIP UP SKIP DOWN
B H
SKIP UP SKIP DOWN
E H
SKIP UP SKIP DOWN
F H
SKIP UP SKIP DOWN
T H
SKIP UP SKIP DOWN
A L
SKIP UP SKIP DOWN
B L
SKIP UP SKIP DOWN
E L
SKIP UP SKIP DOWN
F L
SKIP UP SKIP DOWN
P-MODE
P-MODE
* In the specific setting display state the setting change digit changes when the [P-MODE] key is pressed. (In case of RF side gain setting change does not occur since there is only one digit.) • 2-digit setting  1st digit (initial value) 2nd value  • 3-rd digit setting  1st digit (initial value) 2nd value 3rd digit
P-MODE
P-MODE
P-MODE
* When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set.
L O N P
L O N R
* In laser ON state (without disc) the laser power is changed as follows when the [BASS] key is pressed.
L O N M
Play power Max. power
BASS BASS
BASS
Record power
: RF side focus gain coarse adjustment : A-ATT (focus) tentative setting : B-ATT (focus) tentative setting : ABMXO measurement value display "REPEAT" mark lighting
R F g S a S b
A B
DISP
DISP
* In the setting display sate the value of selected digit changes in the range of "0h to Fh" when [VOL UP/DOWN] key is pressed. However, the RF side gain setting changed in the range of "0h to 6h". * When the [DISP] key is pressed, the display changes as follows.
• ABMAXO Measurement value
: RF side TCRS gain adjustment : TCRSMIO measurement value display "REPEAT" mark lighting
R C G
T C
DISP
DISP
• TCRSMIO Measurement value
: E-ATT (tracking) initial setting : LPFEINO measurement value display "REPEAT" mark lighting : EFMIO measurement value display "REPEAT", "1" mark lighting
S E
e i
E F
DISP
DISP
DISP
• LPFEINO/EFMIO Measurement value
: F-ATT (tracking) initial setting : LPFEINO measurement value display "REPEAT" mark lighting : EFMIO measurement value display "REPEAT", "1" mark lighting
S F
f i
E F
DISP
DISP
DISP
• LPFEINO/EFMIO Measurement value
: RF side focus gain coarse adjustment : A-ATT (focus) initial setting : B-ATT (focus) initial setting : LPFABO measurement value display "REPEAT" mark lighting
R F G S A S B
a b
DISP
DISP
• LPFABO Measurement value
: RF side pit section tracking gain adjustment : Pit section adjustment COUT level setting : RF side groove section tracking gain adjustment : Groove section adjustment COUT level setting
: LPFEFO measurement value display "REPEAT" mark lighting
P T G P C H G T G G C H
e f
DISP
DISP
• LPFEFO Measurement value