: Temperature code displayATT manual adjustment menu
: Temperature code display
$ $ : Temperature code
: Laser ON (Play Power)
: Pit section E-ATT (tracking) setting
: ATT setting
: Pit section E-ATT (tracking) setting
: ATT setting
: High reflection: A-ATT (focus) setting
: Low reflection: A-ATT (focus) setting
: ATT setting
: TCRS ATT setting
: ATT setting
:Groove section E-ATT (tracking) setting
: ATT setting
:Groove section F-ATT (tracking) setting
: ATT setting
: Low reflection: A-ATT (focus) setting
: ATT setting
: Low reflection: B-ATT (focus) setting
: ATT setting
: High reflection pit section B-ATT (focus) setting
: Low reflection pit section B-ATT (focus) setting
: Low reflection groove section B-ATT (focus) setting
: ATT setting
Continuous playback (pit section)
Continuous playback (groove section)
# # # # : Address
PLAY
M A N U 2
ATT Manual Adjustment
T M P $ $
L O N P
L O N P
L O N R
SKIP UP SKIP DOWN
P E
SKIP UP SKIP DOWN
P F
SKIP UP SKIP DOWN
H A
L a
SKIP UP SKIP DOWN
: High reflection: B-ATT (focus) setting
: Low reflection: B-ATT (focus) setting
: ATT setting
H B
L b
SKIP UP SKIP DOWN
G C
SKIP UP SKIP DOWN
H B
L b
L B
S Q # # # #
A P # # # #
PLAY
P-MODE
G E
SKIP UP SKIP DOWN
G F
SKIP UP SKIP DOWN
L A
SKIP UP SKIP DOWN
L B
SKIP UP SKIP DOWN
* When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set.
* In B-ATT setting state, the continuous playback is started when the [PLAY] key is pressed.
When in the continuous playback state the ATT manual adjustment B-ATT setting state is
started when the [P-MODE] key is pressed in continuous playback state.
* In laser ON state (without disc) the laser power is changed as follows if the [BASS] key is pressed
(record/playback machine only).
L O N M
Play power Max. power
BASS BASS
BASS
Record power
P-MODE
P-MODE
P-MODE
* In the specific setting display state the setting change digit changes when the [P-MODE] key is pressed.
1st digit (initial value) 2nd value 3rd digit
* In the specific setting display state the selection digit value changes in the range of "0h to Fh"
when [VOL UP/DOWN] key is operated.
* When the [DISP] key is pressed, the display changes as follows.
: High reflection pit section A-ATT (focus) setting
: High reflection pit section B-ATT (focus) setting
: Low reflection pit section A-ATT (focus) setting
: Low reflection pit section B-ATT (focus) setting
: Low reflection groove section A-ATT (focus) setting
: Low reflection groove section B-ATT (focus) setting
: LPFABO measurement value display
"REPEAT" mark lighting
H A
H B
L a
L b
L A
L B
a b
DISP
DISP
• LPFABO Measurement value
: Pit section E-ATT (tracking) setting
: Groove section E-ATT (tracking) setting
: LPFEINO measurement value display
"REPEAT" mark lighting
: EFMIO measurement value display
"REPEAT", "1" mark lighting
P E
G E
e i
E F
DISP
DISP
DISP
• LPFEINO/FEMIO Measurement value
: Pit section F-ATT (tracking) setting
: Groove section F-ATT (tracking) setting
: LPFEINO measurement value display
"REPEAT" mark lighting
: EFMIO measurement value display
"REPEAT", "1" mark lighting
P F
G F
f i
E F
DISP
DISP
DISP
• LPFEINO/FEMIO Measurement value
: TCRS ATT setting
: TCRSMIO measurement value display
"REPEAT" mark lighting
G C
T C
DISP
DISP
• TCRSMIO Measurement value
To Next Page
Loading...
