3
EMC (this machine and peripheral
devices)
WARNING:
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could
void the user’s authority to operate this equipment.
A Cable of 10 m or less is preferable.
Wireless LAN
MX-M2630/M3050/M3550/M4050/M5050/M6050: Optional (MX-EB18)
MX-M3070/M3570/M4070/M5070/M6070: Standard (Built-in type)
The communication range of wireless LAN may shorten or
communication may not be possible in some usage environments,
due to shielding materials, the installation location, the effects of
ambient radio noise, data transmission speed, and other factors.
Symbols in this manual
To ensure safe use of the machine, this manual uses various
safety symbols. The safety symbols are classified as explained
below. Be sure you understand the meaning of the symbols
when reading the manual.
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated
in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
Meaning of the symbols
WARNING CAUTION
Indicates a risk of death or
serious injury.
Indicates a risk of human
injury or property damage.
CAUTION!
HOT
DO NOT
DISASSEMBLE
PINCH POINT KEEP
CLEAR
MANDATORY
ACTIONS
PROHIBITED
ACTIONS
Power notes
WARNING
Be sure to connect the power cord only to a power
outlet that meets the specified voltage and current
requirements. Also make certain the outlet is
properly grounded. Do not use an extension cord
or adapter to connect other devices to the power
outlet used by the machine.
Using an improper power supply may cause fire or
electrical shock.
* For the power supply requirements, see the name
plate on the left side of the machine.
Do not damage or modify the power cord.
Placing heavy objects on the power cord, pulling it, or
forcibly bending it will damage the cord, resulting in
fire or electrical shock.
Do not insert or remove the power plug with wet
hands.
This may cause electrical shock.
CAUTION
When removing the power plug from the outlet, do
not pull on the cord.
Pulling on the cord may cause damage such as wire exposure
and breakage, and may result in fire or electrical shock.
If you will not use the machine for a long time, be
sure to remove the power plug from the outlet for
safety.
When moving the machine, switch off the main
power and remove the power plug from the outlet
before moving.
The cord may be damaged, will create a risk of fire or
electrical shock.
Installation notes
CAUTION
Do not install the machine on an unstable or
slanted surface. Install the machine on a surface
that can withstand the weight of the machine.
Risk of injury due to the machine falling or toppling.
If peripheral devices are to be installed, do not install
on an uneven floor, slanted surface, or otherwise
unstable surface. Danger of slippage, falling, and
toppling. Install the product on a flat, stable surface
that can withstand the weight of the product.
Do not install in a location with moisture or dust.
Risk of fire and electrical shock.
If dust enters the machine, dirty output and machine
failure may result.
!mxm6070_us_sg.book 3 ページ ２０１８年３月５日 月曜日 午後４時５２分
To Next Page
Loading...
