SPC547 IM 8/2/2018
FEATURES:
1. LOUD/SOFT switch
2. HOUR button
3. MINUTE button
4. TIME button
5. ALARM button
6.ALARM ON/OFF switch
7. SNOOZE button
8. AL indicator Dot
9. PM indicator Dot
10. USB charging port
11. BATTERY door
Model : SPC547
Thank you for your purchase of this quality clock. The utmost care has gone into the design and manufacture
of your clock. Please read these instructions and store them in a safe place for future reference.
POWER SUPPLY
•
Begin by plugging in the power cord into a standard household outlet. The display will flash indicating it needs
to be set.
SETTING THE TIME
•
Press and hold the TIME button down to activate time setting.
•
While holding down the TIME button, press the HOUR button to advance to the correct hour. The PM indicator
will light when the hour is advanced into the PM time.
•
While holding down the TIME button, press the MINUTE button to advance to the correct minute.
•
Release the TIME button when the correct time is shown on the display.
SETTING THE ALARM
•
Press and hold the ALARM SET button down to activate alarm setting.
•
While holding down the ALARM button, press the HOUR button to advance to the correct hour. The PM
Indicator will light when the hour is advanced into the PM time.
•
While the holding down the ALARM button, press the MINUTE button to advance to the correct minute.
•
Release the ALARM button when the correct alarm time is shown on the display.
USING THE ALARM
•
Slide the ALARM ON/OFF switch to the ON position, On the front of the clock the Alarm Indicator dot will
be lit.
•
Slide the ALARM ON/OFF switch to the OFF position to deactivate the alarm. The Alarm Indicator dot will no
longer be visible.
USING THE SNOOZE
•
Pressing the SNOOZE button when the wake-up alarm is sounding will cause the alarm to stop and the alarm will
sound again in nine minutes. This will happen each time when the SNOOZE button is pressed.
SETTING THE ALARM VOLUME
Slide the LOUD/SOFT switch to select the LOUD or SOFT alarm volume level.
LED Alarm Clock with USB Port
Instruction Manual & Warranty
6
1
2
3
4
5
6
7
8
9
10
11
USB CHARGING FUNCTION
•
Conveniently charge your Smartphone.
•
To charge, connect your USB device to the USB port of this alarm.
•
Use only with devices that require 5V USB power. USB port provides 2000mA recharging current.
•
Devices requiring more than 2000mA should not be used. Charging time may vary for different devices.
NOTE: Charging function may not be supported for all phones or electronic devices.
BATTERY BACK UP
•
Remove the BATTERY DOOR and insert two new “AAA” batteries (not included) in the direction of the polarity symbols.
•
Please make sure the batteries are new and inserted correctly.
•
The battery will hold the ALARM and TIME settings if the power is interuppted. There will be no display under battery
power and the ALARM will sound at the correct time. If there is no battery and the power is interrupted, the display will
flash 12:00 and the ALARM / TIME will need to be reset.
BATTERY WARNING
•
Clean the battery contacts and also those of the device prior to battery installation.
Follow the polarity (+) and (-) to place battery.
•
Do not mix old and new batteries.
•
Do not mix Alkaline, Standard (Carbon - Zinc), or Rechargeable (Nickel - Cadmium) batteries.
•
Incorrect battery placement will damage the clock movement and battery may leak.
•
Exhausted battery is to be removed from the product.
•
Remove batteries from equipment which is not to be used for an extended period of time.
•
Do not dispose of batteries in fire. Batteries may explode or leak.
CARE OF YOUR CLOCK
•
Replace the back up battery annually, or store the clock without a battery when not in use. A soft cloth or a
paper towel may be used to clean your clock. Do not use any corrosive cleaner or chemical solutions on the
clock. Keep the clock clean and dry to avoid any problems.
To Next Page
Need help?
General
