PREPARATION FOR USE
■ Connecting the AC power lead
AC 230 V, 50Hz
To an AC socket
To AC INPUT
Connect the AC power lead to the AC power input
socket, then connect the AC power lead plug to an
AC socket.
Notes:
● Unplug the AC power lead from the AC socket if
the unit is not to be used for a prolonged period
of time.
● Never use a power lead other than the one sup-
plied. Otherwise, a malfunction or an accident
may occur.
Notes concerning use:
● Replace the batteries if the operating distance is
reduced or if the operation becomes erratic.
● Periodically clean the transmitter LED on the re-
mote control and the sensor on the main unit
with a soft cloth.
● Exposing the sensor on the main unit to strong
light may interfere with operation. Change the
lighting or the direction of the unit.
● Keep the remote control away from moisture,
excessive heat, shock, and vibrations.
0.2m - 6m
(8” - 20”)
■ Remote control
RESETTING THE MICROCOMPUTER
1
3
3
2,3
AC INPUT
Reset the microcomputer under the following
conditions:
● To erase all of the stored memory contents (clock
and timer settings, and tuner and CD presets).
● If the display is not correct.
● If the operation is not correct.
1
Press the ON/STAND-BY button to enter the
stand-by mode.
2
Unplug the AC power lead from the AC INPUT
socket on this unit.
3
Whilst pressing down the MEMORY/SET but-
ton and the
button, plug the AC power lead
into the AC INPUT socket on this unit.
Caution:
● The operation explained above will erase all data
stored in memory, such as clock and timer set-
tings, and tuner and CD presets.
SETTING THE CLOCK
1
Press the CLOCK/TIMER/SLEEP button to en-
ter the time check mode.
2
Within 3 seconds, press the MEMORY/SET but-
ton.
3
Turn the jog dial to select the time display mode.
0:00 AM 12:00
“0:00” → The 24-hour display will appear.
(0:00 - 23:59)
“AM 12:00” → The 12-hour display will appear.
(AM 12:00 - PM 11:59)
● Note that this can only be set when the unit is
first installed or it has been reset (see page 26).
4
Press the MEMORY/SET button.
5
Adjust the hour by turning the jog dial.
● When the jog dial is turned one click clockwise,
the time will increase by 1 hour. When it is turned
one click anti-clockwise, the time will decrease
by 1 hour.
Keep turning the jog dial to change the time con-
tinuously.
● When the 12-hour display is selected, “AM” will
change automatically to “PM”.
(Main unit operation)
In this example, the clock is set for the 24-hour
(0:00) system.
CLOCK/TIMER/
SLEEP
MEMORY/SET
Jog dial
6
Press the MEMORY/SET button.
7
Adjust the minutes by turning the jog dial.
● When the jog dial is turned one click clockwise,
the time will increase by 1 minute. When it is
turned one click anti-clockwise, the time will de-
crease by 1 minute.
Keep turning the jog dial to change the time con-
tinuously.
● The hour setting will not advance even if min-
utes advance from “59” to “00”.
8
Press the MEMORY/SET button.
● The clock starts operating from “0” second. (Sec-
onds are not displayed.)
Note:
● In the event of a power failure or when the AC
power lead is disconnected, the clock display will
go out.
When the AC power supply is restored, the clock
display will flash on and off to indicate the time
when the power failure occurred or when the AC
power lead was disconnected.
If this happens, follow the procedure below to
change the clock time.
To change the clock time:
Perform steps 1, 2 and 4 - 8 above.
To change the time display mode:
1
Perform steps 1 - 3 in the section “RESETTING
THE MICROCOMPUTER”, on page 26.
2
Perform steps 1 - 8 above.
To Next Page
Loading...
Need help?
General
