8
General Operation
Standby/ON
When you rst connect the unit to the main socket, the unit will be in
STANDBY mode. Press the
button on the remote control to switch the
main unit ON or OFF.
• When turning the system on, the system will start in the same mode as
during switch o .
• Disconnect the mains plug from the mains socket if you want to switch
the unit o completely.
• If there is no signal under the CD, USB, BT (Bluetooth) or AUX mode,
the unit will automatically switch o within 15 minutes.
Select Modes
Press the button repeatedly on the unit or press the CD/AUX, FM/DAB,
USB or BT PAIR buttons on the remote control to select the desired mode.
The selected mode will show on the display.
Adjust the Volume
• Press the VOL +/– buttons on the remote control or turn the VOLUME
+/- dial on the unit to adjust the volume.
• If you wish to turn the sound o , press the
button on the remote
control. Press the
button again or press VOL+/- button on the remote
control or turn the VOLUME +/- dial on the unit to resume normal
volume.
Select the Equaliser
Press the EQ button on the remote control or on the unit repeatedly to
select: [Pop] - [Classic] - [Jazz] - [Rock] - [Flat]
Adjust the Brightness
Press the DIMMER button on the remote control to select brightness level.
Adjust the Bass
Press the BASS button on the remote control to enable and disable the
bass enhancement.
Set the Sleep Timer
This unit can switch to standby automatically after a set period of time.
1. Press the TIMER/SLEEP button on the remote control repeatedly to
select your desired time. The number of minutes will display in below
sequence: SLEEP 90 -> SLEEP 60 -> SLEEP 30 -> SLEEP 15 -> SLEEP 00
2. Stop pressing the SLEEP button when your desired time is displayed.
The sleep timer is now set.
Press the SLEEP button to view the remaining time before switch o .
To cancel the sleep timer, press the SLEEP button
repeatedly until “SLEEP 00” shows on the display.
AUX Operation
1. Ensure that the unit is connected to the TV or audio device.
2. Press the
button on the main unit repeatedly or press the CD/AUX
button on the remote control to select AUX mode.
3. Operate your audio device directly for playback features.
4. Press the VOL +/– button to adjust the volume to your desired level.
CD/USB Operation
Tips:
• Supported MP3-CD formats is MP3 / CD.
• Unsupported le formats are skipped. For example, Word documents
(.doc) or MP3 les with extension .dlf are ignored and not played.
• USB supports maximum memory is 64GB.
CD Operation
1. Press the button repeatedly on the unit or press the CD/AUX
button on the remote control to select DISC mode.
2. Press the
button on the unit or on the remote control and the disc
tray will open automatically.
3. Place the CD/MP3 disc with the label side up into the CD
compartment, and then press the
button on the unit or on the
remote control to close the disc tray.
The current playing time of the track will be shown on the display,
and unit will play the rst track on the CD/MP3 disc automatically.
If there is no disc or the disc can’t be read,
“NO DISC” will show on the display.
USB Operation
1. Insert the USB stick on the back of the unit.
2. Press the
button on the main unit repeatedly or press the USB
button on the remote control to select USB mode.
Play Control
• To stop play, press the button on the remote control. The total tracks
of the CD will show on the display.
• To pause or resume play, press the
button on the unit or the /
SCAN button on the remote control.
• To skip to the previous/next track, press the
/ buttons on the unit
or on the remote control.
• Press and hold the
/ buttons on the unit or on the remote control
to perform fast forward/reverse playback. Release the button to resume
normal playback.
• Press the ALBUM/PRESET
, buttons to skip to the previous/next
album (only for MP3/WMA discs).
• Press the INFO button on the remote control to display the current play
information.
Intro Playback
• Press the INTRO button on the remote control. The unit will play the rst
10 seconds of each track.
• Press the INTRO button on the remote control again to resume normal
playback.
Random Playback
• Press the SHUFFLE button on the remote control or the MODE button
on the unit to switch the randomly play the song ON/OFF.
SHUFFLE: Randomly play the song. “
” lights up.
SHUF OFF: Randomly turned o .
To Next Page
Loading...
Need help?
General
