Sharp XL-T300H

– 7 –
XL-T300H
2
2
Accessories
1
1
AM loop aerial x 1AC power lead x 1 Remote control x 1
123
Battery installation of remote control
Use 2 “AAA” size batteries (UM-4, R03, HP-16 or similar).
Batteries are not included.
Remove the Insert the batteries Replace the cover.
battery cover. as shown.
FM aerial x 1
Speaker wire x 2
"AAA" size battery (UM-4,
R03,HP-16 or similar)
(Except for U.K.)
2
(Except for U.K.) (For U.K.)
System Connections
3
3
Right speaker
Left
speaker
Connection cable
for digital recording
(not supplied)
MD recorder
To the optical line
input socket
Wall socket
(AC 230 V, 50 Hz)
To the line
output sockets
RCA lead
(not supplied)
FM aerial
AM loop aerial
VCR, DVD, etc.
TV
Right speaker
Left speaker
Black
White line
(CD only)
Headphones
(Except for U.K.)
(For U.K.)
Press the ON/STAND-BY button to turn the power on.
Turn on your System
4
4
Listening to a CD
1
Press the FUNCTION button
until “CD STOP” appears on
the display.
If no disc is loaded, the display will
be “NO DISC” instead of “CD STOP”.
2
Press the
77
77
7 OPEN/CLOSE
button to open the CD/Cas-
sette compartment.
3
Place a CD on the spindle,
label side up.
4
Press the
77
77
7 OPEN/CLOSE
button to close the CD/Cas-
sette compartment.
5
Press the
0606
0606
06 button to start
playback from track 1.
Listening to the Radio
1
Press the FUNCTION button
until “FM” or “AM” appears
on the display.
2
Press the TUNING (
XX
XX
X or
WW
WW
W)
button to tune in to the de-
sired station.
When the TUNING button is pressed
for more than 0.5 seconds, scanning
will start automatically and the tuner
will stop at the first receivable broad-
cast station.
3
To receive an FM stereo trans-
mission:
Press the FUNCTION button
to display the “ST” indicator.
“j” will appear when an FM
broadcast is in stereo.
FM stereo mode indicator
FM stereo receiving indicator
■ If trouble occurs
When this product is subjected to strong external interference (mechanical shock, excessive static
electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may mal-
function.
If such a problem occurs, do the following:
1 . Set the unit to the stand-by mode and turn the power on again.
2 . If the unit is not restored in step 1, unplug and plug in the
unit, and then turn the power on.
3 . If neither step 1 nor 2 restores the unit, do the following:
1
Press the ON/STAND-BY button to enter the power stand-by
mode.
2
Unplug the AC power lead from the AC INPUT socket on the
unit.
3
Whilst pressing down the VOLUME
X
button and the
44
44
4
button, plug the AC power lead into the AC INPUT socket on the unit.
Caution:
This operation will erase all data stored in memory including clock, timer settings, tuner preset, and
CD programmed.
■
Maintenance
Cleaning the CD pickup lens
Do not touch the laser pickup lens. If fingerprints or dust accumulate
on the pickup, clean it gently with a dry cotton swab.
Cleaning the tape-handling parts
• Dirty heads, capstan or pinch roller can cause poor sound and
tape jams. Clean these parts with a cotton swab moistened with
commercial head/pinch roller cleaner or isopropyl alcohol.
• When cleaning the heads, pinch roller, etc., unplug the unit which
contains high voltages.
A
Erase head C Capstan
B
Recording/Playback head D Pinch roller
• After long use, the deck’s heads and capstan may become magnetised, causing poor sound.
Demagnetise these parts once every 30 hours of playing/recording time by using a commercial
tape head demagnetiser. Read the demagnetiser’s instructions carefully before use.
AC INPUT
D
A
B
C
Listening to a Cassette Tape
1
Press the FUNCTION button
until “TAPE” appears on the
display.
2
Press the
77
77
7 OPEN/CLOSE
button to open the CD/Cas-
sette compartment.
3
Load a cassette into the cas-
sette compartment with the
side to be played facing up.
4
Press the
77
77
7 OPEN/CLOSE
button to close the CD/Cas-
sette compartment.
5
Press the
0606
0606
06 button to start
playback.