Several minutes after power-on, accuracy is not guaranteed. Reaches the accuracy level within 5 minutes after power-on.
Tracking of a reference
junction ：Below the ambient temperature of 0.5 ℃ / min, compensation accuracy of reference junction ±１℃
Resistance bulb stipulated
current resistance bulb ：Approx. 0.25mA
Lead wire resistance
tolerance level ：5Ω or less per wire (Resistance of three lines should be equal)
Influence of lead-wire
resistance ：5Ω or less per wire 0.2%FS
10Ω or less per wire 0.5%FS
20Ω or less per wire 1.0%FS
Measuring range ：Item 5-5. Refer to measuring range code table.
Voltage (mV) Input resistor ：500kΩ or more
Input voltage range ：Item 5-5. Refer to measuring range code table.
Voltage input (V) Input resistor：500kΩ or more
Input voltage range ：Item 5-5. Refer to measuring range code table.
Current input (mA) reception
Resistance ：250Ω (built-in)
Input range ：Item 5-5. Refer to measuring range code table.
Sampling period ：0.25 second
PV filter ：0 - 9999 second
PV offset compensation ：±500 unit
PV gain correction ：±5.00%PV filter
Control
Control system ：PID control with an auto tuning function or ON-OFF operation
Proportional band (P) ：OFF and 0.1 - 999.9% of measuring range (ON-OFF operation by OFF setting)
ON-OFF Differential-gap (DF) ：1 - 999 unit
Integration Time (I) ：OFF, 1- 6000 seconds (PD operation by OFF setting) If both I and D are OFF, P operation.
Manual Reset (MR) ：±50.0% (effective when set as I = OFF)
Output 2 dead band ： -1999 - 5000 unit
Output limiter (OL, OH) ：0.0 - 100.0% (OL<OH) (set resolution 0.1)
Soft start ：OFF, 0.5 - 120.0 seconds (set resolution 0.5)
Proportional period ：0.5 - 120.0 seconds (set resolution 0.5)
Control output characteristic ：Output 1, output 2. Possible to choose either RA (heating) or DA (cooling).
Manual output ：0.0 - 100.0% (set resolution 0.1)
＊ Each parameter,( P, I, D, DF, MR, OL, and OH) of Outputs 1 and Outputs 2, Flex PID belongs to 1～3 categories.
Control output 1
Contact ：normal open (1a) 240V AC 2A (resistance load)
Voltage pulse (SSR drive) ：12V DC+1.0--1.5V MAX20mA
Current ：4 - 20mA DC load resistance 500Ω or less Display accuracyaccuracy±1% (accuracy maintenance range 23℃±5℃)
Load regulation ±0.2%, resolution approx. 1/12000
Control out put 2 (option) ：Control out put 2 is exclusive option of event 3 and DI4.
Contact ：normal open (1a) 240V AC 2A (resistance load)
Voltage pulse (SSR drive) ：12V DC+1.0--1.5V MAX20mA
Current ：4 - 20mA DC load resistance 500Ω or less ,display accuracy±1% (accuracy maintenance range 23℃±5℃ )
Load regulation ±0.2%, resolution approx. 1/200
Program function (option)(40step fuinction add from Ver 1.3*)
Number of pattern ：Choosen from pattern 1,2,4 Add from Ver 1.3*
Number of steps ：Maximum 40steps When choose pattenn 1,20steps of each steps when choose pattern 2,10steps of each steps when choose pattern 4.
PID selection ：Each output has three kinds. PID1, PID2, and PID3.
Time setting ：0 minute 0 second～99 minutes 59 seconds or 0 hour 0 minute～99 hours 59 minutes or 0.0 - 999.9 hours ,and ∞ (infinity)
Time setup resolution ：1 second or 1 minute or 0.1 hour
Time accuracy ：± (Setup time × 0.005 +0.25 second)
In a step Setting parameter ：SV, time, PID№
Number of repeats ：1 - 9999 times, and ∞
Time signal ：Possible to allot to Event (1 second for changeover, 3 seconds for patter end, 3 seconds for program end)
PV start function ：With
Guarantee soak function ：With Off or 1-2000unit(add from Ver 1. 2*)
Time hold facility ：Possible at front key, DI allotment, or communication
Step skip ：Possible at front key, DI allotment, or communication
Power failure compensation ：without (setting contents being held.However, elapsed time, execution step, and number of execution are reset.)
To Next Page
Loading...
