SHUR-DRI SD106-01 - User Manual

Questions and Answers

W
williamdavidsonAug 6, 2025
Why does my SHUR-DRI SD106-01 stop without warning?
- S
  Sarah BrooksAug 6, 2025
  If your SHUR-DRI Water Pump stops without warning, it might have overheated, causing the thermal overload to trip. In this case, wait for the overload to reset; the pump will automatically restart. Other potential causes include a discharge hose that's too long or a discharge lift higher than 28 feet (use a shorter hose or reduce the lift), the pump body not oiled (add oil through the inlet port), a suction hose that's too long or too small (use a 1/2" suction hose, 25’ long or less), a worn impeller (replace it), suction leaks (replace the hose washer and check for leaks), or a suction hose that's kinked or coiled (straighten it out).
S
Sandra SmithAug 13, 2025
What to do if SHUR-DRI Water Pump runs, but pumps little or no water?
- A
  Angel ClarkAug 13, 2025
  If your SHUR-DRI Water Pump runs but pumps little or no water, the impeller may be worn, and you should replace it. Also, inspect the motor brushes and replace them if they are bad. Check the U-cup shaft seal and replace it if it's bad, as this can cause leaks. Ensure that the suction or discharge hose isn't kinked or coiled; if it is, straighten it out.
W
Wayne CrosbyAug 21, 2025
How to fix SHUR-DRI Water Pump that won’t prime?
- C
  Christopher StoneAug 21, 2025
  If your SHUR-DRI Water Pump won’t prime, several factors could be the cause. Make sure the discharge hose isn't too long or the discharge lift isn't higher than 28 feet; if it is, use a shorter hose or reduce the lift. Check if the pump body needs oiling by adding oil through the inlet port. Ensure the suction hose is a 1/2" suction hose, 25’ long or less. A worn impeller can also prevent priming, so consider replacing it. Suction leaks can also be the issue; replace the hose washer and inspect the hose for leaks. Finally, make sure the suction hose isn't kinked or coiled; straighten it out if it is.
L
Laura BauerAug 28, 2025
Why is my SHUR-DRI SD106-01 leaking?
- S
  smithalexisAug 28, 2025
  If your SHUR-DRI Water Pump leaks, it could be due to a leaking shaft U-cup seal, in which case you should replace the shaft seal. Alternatively, the cover O-Ring might be leaking, requiring you to replace the cover O-Ring.

Summary

SHUR-DRI Flexvane Pump Installation Manual

Consumer Support and Contact Information

Provides the consumer hot-line number, operating hours, and company address for support.

Safety Precautions for Pump Operation

Electrical Shock and Burn Hazards

Details critical safety information, including electrical hazards, burn risks, and operational limitations.

Pump Installation Procedures

Pump Oiling and Hose Connection

Step-by-step guide for oiling the pump and connecting inlet/outlet hoses correctly.

Hose Routing and Water Management

Instructions on proper hose placement, ensuring water flow, and keeping the motor dry.

Pump Unplugging, Performance, and Maintenance

Covers unplugging the pump, performance specifications, disassembly, and reassembly procedures.

Troubleshooting and Component Reference

Troubleshooting Common Pump Problems

A guide to diagnosing and resolving common issues with the pump's operation.

Component Identification and Service Kits

Visual reference of pump parts and available service kits for maintenance or repair.

Product Warranty Information

Limited Warranty Terms and Claims

Details the warranty period, coverage, and how to make a claim for defective products.

Warranty Exclusions and Conditions

Outlines specific conditions and uses that are not covered by the product warranty.

SHUR-DRI SD106-01 Specifications

General

Model	SD106-01
Category	Water Pump
Type	Submersible
Voltage	115V
Horsepower	1/6 HP
Flow Rate	1800 GPH
Max Head	25 ft
Discharge Size	1-1/4 in
Cord Length	10 ft
Power Cord Length	10 ft