222
HARTREY AVE
EYlNSTDN
11
60104
il
S
A
AREACODE
31118667200.
LAtlLt bHJRtMICWO
TWX:
910-231-0048
TELEX:
72-4381
THE PREMIER FAMILY OF STEREO SOUND REPRODUCERS
STEREO DYNETIC@
M95ED
PHONOGRAPH CARTRIDGE
CARTRIDGE AND STYLI SPECIFICATIONS
2.
Connect leads to cartridge (see
Figure
1).
3. Lay cartridge in shell and align
mounting holes on side of car-
tridge with holes or threads in
shell. Follow turntable manu-
facturer's instructions to mount
N95ED
5
X
l8y
(.0002
X
.0007 in.)
Biradial
(Elliptical)
N95-3f
63 microns
(.0025 in.)
Spherical
cartridge in tone arm or plug-in
shell.
4. Reinsert stylus (see Stylus Re-
placement). FIGURE
2
RECOMMENDED STYLUS CLEANING:
Use a camel's hair brush (No. 2
srze
or smaller), trimmed to approximately 6 mni (1/4 in.), dipped in alcohol or
an alcohol-distilled water solution. Commercial cleaning solutions may cause
stylus damage or corrosion. Always brush stylus from back to front; never
brush or wipe stylus from front to back or side to side.
TO PRESERVE STYLUS LIFE:
1.
Follow turntable or tone arm instructions when adjusting antiskating
force.
2.
Do not handle the tone arm while it is in operation since this may
cause the arm to sweep across the record.
3. If it is necessary to manually place the tone arm in the record groove
while turntable is rotating, release it as soon as the stylus engages the
record groove.
4. Correct improper set-down adjustment or malfunction of the turntable
changrng mechanism to prevent the stylus irom strrklng the edge of the
turntable or record. Do not stack more records than turntable
manuiac-
turer recommends.
5.
Take care to properly insert the stylus into the cartridge assembly and
the cartridge and shell assembly into the tone arm receptacle.
6.
Use proper vertical tracking force setting for each cartridge.
7.
Do not use badly warped, cracked or imperfect records.
8. When dusting the turntable protect the stylus with the stylus guard.
SPECIAL NOTE:
To maintain the
orig~nal performance standards of your
cartridge, be certain that any replacement stylus you buy bears the follow-
ing certification on the package: "This Stereo
Dynetic8 stylus is
precision
manufactured by Shure Brothers Inc." AVOID INFERIOR IMITATIONS. THEY
WILL SERIOUSLY,,DECRADE THE PERFORMANCE OF YOUR CARTRIDGE.
ALL GENUINE
DYNETIC@" STYLI ARE MANUFACTURED BY SHURE
BROTHERS
INC. LOOK FOR THE NAME SHURE ON THE STYLUS GRIP.
For more information on your Shure stylus, write for booklet:
"A
Visit to
the
Small World of a Stylus."
FULL ONE-YEAR WARRANTY: Shure Brothers lncorporated
("Shure"),
222 Hartrey Avenue, Evanston,
Illinois 60204, warrants to the owner of
thrs
product that rt will be free, in normal use, of any defects in workmanship
and
materrals lor a period of one year from date of purchase. You should
retain
proof of date of purchdse. Shure
18
not liable for any consequentral
damages. It this Shure product has any defects as described above, care-
fully repack the unit and return it prepaid to:
Shure Brothers lncorporated
Attention: Service Department
1501 West Shure Drive
Arlington Heights, Illinois 60004
If you are not in the United States, return the unit to your dealer
or
Authorized Service Center for repair. The unit will be repaired or replaced
and returned lo you promptly, and
if it cannot be repaired or replaced,
you may elect to receive a refund.
Thrs warranty does not include stylus wear.
PATENT NOTICE:
Cartridge
and stylus manufactured under one or more
of the following U.S. patents: 3,055,988, 3,077,521, 3,077,522, and 3,463,889.
Copyright 1981, Shure Brothers Inc.
27A1247 (AH) Printed in U.S.A.
toptional
78
rpm Stylus: Set amplifier to "MONO" or "A+B."
'Output voltages given for stereo cut record. For MONO cut record,
output voltage at both left channel and right channel cartridge terminals
will be 71% of figures above.
"Tracking forces
greatel than maximum ind~cated should not be used.
NET WEIGHT:
6.3
grams
INDUCTANCE: 650 mlllihenrres
DC RESISTANCE: 1550 ohm?
OPTIMUM LOAD: 47,000 ohms resrstance in parallel wlth 400 to 500 prco-
farads total capacitance per channel. (Load resistance can be as high ar
100,000 ohms and total capacltance can be as low as 100 prcofarads wrth
only mrnor audlble change.) Total capacrtance ~ncludes the capacitances of
the tone arm
wrrlng, phono cables, and the ampllfler input circurt.
FOUR-CHANNEL: This Stereo
Dynetic@ cartridge is compatible with all
four-channel matrix systems.
MONOPHONIC OPERATION: Set
iunct~on swltch on ampl~frer to "MONO"
or
"A+B." If amplrfier is not equlpped with this swttch, connect left and
right channels
In parallel.
CONNECTIONS (see Figure
1):
Right "hot" lead (usually red) to "R," rrght
ground (usually green) to "KG." Left "hot" lead (usually whrte) to "L,"
left ground (usually blue) to
"LC." If metal head is causing ground loop
hum, remove the ground tab. The
metalllc cartr~dge shleld is
disconnected
from the right channel ground by the removal of the ground tab.
CAUTION: Do not make solder
i;JT;;;;F,
connection to cartridge terminals.
STYLUS REPLACEMENT (see
Fig-
ure
2):
Grasp molded housing of
stylus and gently pull forward
out of cartridge.
Insert replace-
ment stylus into socket and press
until housing mates with cartridge
S~O~~O
C""""i
(BLYL
anel
case.
FlQURE
1
GREEN
RING1
MOUNTING
112.7
mm
(112
in.)
mounting centers]:
Mounting screws are provided.
1.
Remove stylus guard and stylus
(see
Stylus Replacement).
Yellow
Dark
Green
4.7
mV
5.5
mV
20 to
20,000
Hz
20
to
20,000
Hz
within
2 dB
-
25 dB
at
1
kHz
-
3/q
to
1
grams
1%
to
3
grams
400
Hz
-
24 cm/sec
1,000
Hz
-
33
cm/sec
10,000
Hz
-
19 cm/sec
at
1
gram
--
To Next Page
Need help?
General
