To Next PageTo Next Page
Need help?Do you have a question about the SIEGEN S641G and is the answer not in the manual?
Disconnect spray gun from air supply before maintenance or accessory changes.
Understand product applications, limitations, and specific hazards before use.
Paint cup remains pressurized after disconnecting from air line.
Release pressure by gently opening cup instead of pulling the trigger.
Maintain spray gun in good condition using authorized agent; use recommended parts.
Operate in a clean, tidy, well-lit, and ventilated area, free from unrelated materials.
Keep the spray gun clean for optimal performance and safety.
Ensure air system is suitable for the spray gun's air consumption needs.
Wear approved respiratory protection and safety eye goggles during operation.
Remove loose clothing and jewelry, and tie back long hair for safety.
Keep children and unauthorized persons away from the working area.
Take precautions to avoid unintentional operation of the spray gun.
Never point the spray gun at yourself, others, or animals.
Do not carry the gun by the air hose or pull it from the air supply.
Use the spray gun only for its intended purpose.
Do not permit untrained individuals to operate the spray gun.
Avoid using the spray gun in wet or damp conditions or areas with condensation.
Do not operate if parts are missing or damaged to prevent failure or injury.
Do not direct air from the hose at yourself or others.
Switch off and disconnect from air supply when not in use.
Ideal for various materials with adjustable fan control. Features brass air cap and steel needle/nozzle.
Model numbers S641G and S642G.
Standard and available nozzle sizes for S641G and S642G models.
Recommended air pressure (45psi), air consumption (4cfm), and pot capacity (600ml).
Recommended air supply connection diagram is shown in Figure 1.
Ensure air valve or trigger is off before connecting to air supply.
Use 45psi air pressure; excessive pressure or unclean air causes wear and damage.
Drain air tank daily, clean air inlet filter weekly for optimal performance.
Use 1/4" I.D. hose for lengths over 8m; ensure secure connections.
Keep hose away from heat, oil, sharp edges; check for wear.
Use a leader hose to prevent failure from quick-fit couplings directly on the gun.
Hold gun perpendicular, move parallel; start and end stroke before trigger action.
Spray 6-10 inches away for even, wet coverage; overlap strokes for uniform finish.
Adjust fluid with needle knob, atomizing air with control knob, and air volume with adjustment knob.
Turn air nozzle for horizontal/vertical fan spray; lock with retaining ring.
Horizontal nozzle wings give vertical fan for even coverage when moving gun.
Thorough cleaning after each use is vital for optimum performance.
Flush with clean solvent, use brush for paint, blow clean with air, wipe exterior.
Use soft tools for cleaning nozzles; avoid metal instruments to prevent damage.
Adjust fluid needle valve for air flow before fluid flow when triggered.
Screw parts hand tight to avoid cross-threading; do not use excessive force.
Ensure complete nozzle set is fitted; insert fluid nozzle before paint needle.
Caused by improper cleaning, dried material, or damaged nozzle parts.
Dissolve material in side ports with solvent; do not poke nozzles with metal.
Remove air nozzle, wipe fluid tip, and tighten air nozzle securely.
Regulate material viscosity or reduce air pressure for better atomization.
Check nozzle seating, tighten air nozzle, or replace parts if necessary.
Ensure paint nozzle is tight and air nozzle is screwed on completely.
Recycle unwanted materials and packaging at designated recycling centers.
Dispose of unserviceable products and fluids according to local regulations.
Sealey reserves the right to alter data and specifications without prior notice.
No liability accepted for incorrect use of the product.
Guarantee is 12 months from purchase date; proof of purchase required.
General| Nozzle Size | 1.4mm |
|---|---|
| Model | S641G |
| Air Consumption | 4.5 CFM |
| Operating Pressure | 40 PSI |
| Paint Capacity | 600 ml |
| Power Source | Air Powered |
