Siemens 7SJ511 - Page 133

$SSHQGL[6-
9
&*&
Annunciations 7SJ511 for PC, LC-display and binary inputs/outputs
²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²²
FNo. - Function number of annunciation
Op/Ft - Operation/Fault annunciation
C/CG: Coming/Coming and Going annunciation
M : Measurand
E - Earth fault annunciation
IOT - I: can be marshalled to binary input
O: can be marshalled to binary output (LED, signal relay)
T: can be marshalled to trip relay
¿©©©©§©©©©©©©©©©©©©§©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©§©©§©©§©§©©©¤
FNo.Abbreviation  Meaning OpFtEIOT
¨©©©©ª©©©©©©©©©©©©©ª©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©ª©©ª©©ª©ª©©©
 3>Time Synchro>Time synchronization    IO 
 4>Start FltRec>Start fault recording C   IO 
 5>LED reset >Reset LED indicators    IO 
 7>ParamSelec.1>Parameter set selection 1 (with No.8)    IO 
 8>ParamSelec.2>Parameter set selection 2 (with No.7)    IO 
 11>Annunc. 1 >User defined annunciation 1 CG  IOT
 12>Annunc. 2 >User defined annunciation 2 CG  IOT
 13>Annunc. 3 >User defined annunciation 3 CG  IOT
 14>Annunc. 4 >User defined annunciation 4 CG  IOT
 51Dev.operativeDevice operative / healthy CG O
 56Initial startInitial start of processor system C    
 60LED reset LED Reset C    
 95Param.runningParameters are being set CG O
 96Param. Set A Parameter set A is active CG O
 97Param. Set B Parameter set B is active CG O
 98Param. Set C Parameter set C is active CG O
 99Param. Set D Parameter set D is active CG O
 100Wrong SW-versWrong software-version C    
 101Wrong dev. IDWrong device identification C    
 110Annunc. lost Annunciations lost (buffer overflow) C    
 111Annu. PC lostAnnunciations for PC lost C    
 115Flt.Buff.OverFault annunciation buffer overflow  C   
    
 120Oper.Ann.InvaOperational annunciations invalid CG   
 121Flt.Ann.InvalFault annunciations invalid CG   
    
 123Stat.Buff.InvStatistic annunciation buffer invalid CG   
 124LED Buff.InvaLED annunciation buffer invalid CG   
 129VDEW-StateInvVDEW state invalid CG   
 135Chs Error Error in check sum CG   
 136Chs.A Error Error in check sum for parameter set A CG   
 137Chs.B Error Error in check sum for parameter set B CG   
 138Chs.C Error Error in check sum for parameter set C CG   
 139Chs.D Error Error in check sum for parameter set D CG   
 143Failure 15V Failure of internal 15 VDC power supplyCG   OT
 144Failure 5V Failure of internal 5 VDC power supply CG   OT
 145Failure 0V Failure of internal 0 VDC power supply CG   OT
 154Failure RKA Failure in the RKA module CG   
 159LSA disruptedLSA (system interface) disrupted CG   
 161I supervisionMeasured value supervision of currents   O
 162Failure ÉI Failure: Current summation supervision CG   OT
 163Failure IsymmFailure: Current symmetry supervision CG   OT
 203Flt.RecDatDelFault recording data deleted C    
 204Flt.Rec.viaBIFault recording initiated via bin.inputC    
 205Flt.Rec.viaKBFault recording initiated via keyboard C    
 206Flt.Rec.viaPCFault recording initiated via PC interfC    
¥©©©©¦©©©©©©©©©©©©©¦©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©¦©©¦©©¦©¦©©©¾
www . ElectricalPartManuals . com