Siemens SIMOREG DC Master 6RA7018-6DS22 - Page 201

02.00 Function diagrams
SIEMENS AG 6RX1700-0AD76 8-21
SIMOREG DC Master Operating Instructions
Sheet G136 Ramp-function generator
<1>
y = 0
y
.01 .02
1
≥
.01 .02
.03
.04 .01 .02
.03
.04
<1> <1>
<1>
<1>
1
≥
1
≥
.01 .02
0 0 P303 - P306 0 1 P311 - P314 1 0 P307 - P310 2 3
3210
4567
15
87564321
- G136 -
x
0%
1
0
1
0
&
T0
0 1
.01 .02
1
≥
B0211
r027
P311.F P307.F
P312.F P308.F
P313.F P309.F
P314.F P310.F
dv/dt
P542.F
P636 (1)
K K
K0190
P303.F P304.F
P305.F
P306.F
K0191
K0190
K0192
r028
K0181 K0183 K0170 K0182
P632 (1)
K
K K K
P633 (9)
K K K K
P300.F
P301.F
P634
K
B0206
B0208 B0207 B0209
P641.B (0)
B
P637.B (0)
B
P638.B (0)
B
K
190
WE
0
r316
r315.1 r315.2 r315.3 r315.4
P646.B (1)
B
0: 1: 2: 3: 4: 5: 7:
15:
P317.FP302.F
P318.F
B0161
P319.F (0,05)
(0,00...10,00 s)
P639 (167)
K
P640.B (0)
B
K
B0104
negative setpoint limit
Lowest positive setpoint limit
positive setpoint limit
Limitation after RFG has responded
Highest negative setpoint limit
When P633.0x = 9, the positive limit selected via P632.0x acts with inverted sign as negative limit
Parameter selection
RFG-setting 2 RFG setting 3
Lower transition
rounding
Upper transition
rounding
... RFG setting 3 [s] ... RFG setting 2 [s]
Setpoint
(RFG
output)
Ramp-function
generator input
... RFG setting 1 [s]
from starting integrator control
(see P302)
Time difference [s]
Ramp-up/down
time
Rounding
This changeover to RFG settings 2 and 3 has priority over the input of RFG setting 3 by the starting integrator control
Ramp-function generator
Minimum Maximum
Speed setpoint
Enable setpoint from
control word 1
Ramp-function generator
start from control word 1
ramp-up
ramp-down
RFG active to status word 2
Select bypass
ramp-function
generator
Ramp-function
generator setting
Effective
parameters
n-act +
∆
n-act -
∆
RFG status
Enable ramp-function generator from
control word 1 (with "0"-Signal: y=0)
Enable changeover of starting integrator
Display of RFG status on r316
Ramp-function generator enable Ramp-function generator start Setpoint enable & /OFF1 Set ramp-function generator Track ramp-function generator Bypass ramp-function generator Ramp-down Ramp-up
RFG
tracking
Starting
integrator
Set RFG
on
shutdown
Ramp-up time Ramp-down time
Shutdown
Bypass ramp-function generator from
sheets "Fixed setpoint", "Inching
setpoint", "Crawling setpoint"
Operating state
- -, I or II
ON delay
Setting value
Set ramp-function
generator
Run