Siemens SIPROTEC 7SJ600 - Page 161

$SSHQGL[6-
9
&*&
¿©©©©§©©©©©©©©§©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©§©©§©©§©§©¤
FNo.Text  Meaning OpFtIO
¨©©©©ª©©©©©©©©ª©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©ª©©ª©©ª©ª©
 356>mCLOSE >Manual close CG IO
 501FT det General fault detection of device  CG O
 511DEV.Trp General trip of device  C  O
 521IL1 Interrupted current: Phase L1 (I/In)  C
 522IL2 Interrupted current: Phase L2 (I/In)  C
 523IL3 Interrupted current: Phase L3 (I/In)  C
 563CBA sup CB alarm suppressed    O
 601IL1= IL1 [%] =  M   
 602IL2= IL2 [%] =  M   
 603IL3= IL3 [%] =  M   
 651IL1= Current in phase IL1 =  M   
 652IL2= Current in phase IL2 =  M   
 653IL3= Current in phase IL3 =  M   
1157>CBclo >Circuit breaker closed CG IO
1174CBtest Circuit breaker test in progress CG  O
1185CBtpTST Circuit breaker test: Trip 3pole CG  O
1188CBTwAR Circuit breaker test: Trip w. reclosureCG  O
1501>O/L on >Switch on thermal overload protection   IO
1502>O/Loff >Switch off thermal overload protection  IO
1503>O/Lblk >Block thermal overload protection   IO
1511O/L off Thermal overload prot. is switched off CG  O
1512O/L blk Thermal overload protection is blocked CG  O
1513O/L act Thermal overload protection is active CG  O
1516O/L wrn Thermal overload prot.: Thermal warningCGCG O
1518O/L p/u Thermal overload prot.: Pick-up CGCG O
1521O/L Trp Thermal overload protection trip  C  O
1530THETA = Operating temperature =  M   
1531t Trp = O/L: estimated time to trip  M   
1532t Trp = O/L: estimated time to trip  M   
1533t rel = O/L: estimated time to release closing  M   
1534t rel = O/L: estimated time to release closing  M   
1701>O/Cpon >Switch on O/C protection phase   IO
1702>O/Cpof >Switch off O/C protection phase   IO
1704>O/Cpbk >Block overcurrent protection phases   IO
1711>O/Ceon >Switch on overcurrent protection earth  IO
1712>O/Ceof >Switch off overcurrent protec. earth   IO
1714>O/Cebk >Block overcurrent protection earth   IO
1721>I>>blk >Overcurrent protection: blockstage I>>CG IO
1722>I> blk >Overcurrent protection: block stage I>CG IO
1723>Ip blk >Overcurrent protection: blockstage Ip CG IO
1724>IE>>bk >Overcurrent protec.: blockstage IE>> CG IO
1725>IE> bk >Overcurrent protection: blockstage IE>CG IO
1726>IEp bk >Overcurrent protection: blockstage IEpCG IO
1727>C/O >C/O of overcurrent fault detec. level   IO
1751O/Cpoff Overcurrent prot. phase is switched offCG  O
1752O/Cpblk Overcurrent prot. phase is blocked CG  O
1753O/Cpact Overcurrent prot. phase is active CG  O
1756O/Ceoff O/C protection earth is switched off CG  O
1757O/Ceblk O/C protection earth is blocked CG  O
1758O/Ceact O/C protection earth is active CG  O
1762O/C L1 O/C fault detection phase L1    O
1763O/C L2 O/C fault detection phase L2    O
1764O/C L3 O/C fault detection phase L3    O
1765O/C E O/C fault detection earth    O
1771FD L1 O/C fault detection L1 only  C  O
1772FD L1E O/C fault detection L1-E  C  O
1773FD L2 O/C fault detection L2 only  C  O
1774FD L2E O/C fault detection L2-E  C  O
1775FD L12 O/C fault detection L1-L2  C  O
1776FD L12E O/C fault detection L1-L2-E  C  O
1777FD L3 O/C fault detection L3 only  C  O
1778FD L3E O/C fault detection L3E  C  O
¥©©©©¦©©©©©©©©¦©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©¦©©¦©©¦©¦©¾
www . ElectricalPartManuals . com