Siemens Synco OZW772 Series

s
Synco™, Synco™ living
Web server OZW772... V6.0
Commissioning instructions
OZW772.01
OZW772.04
OZW772.16
OZW772.250
CE1C5701en
2015-10-12 Building Technologies

Siemens Synco OZW772 Series Specifications

General

Brand	Siemens
Model	Synco OZW772 Series
Category	Server
Language	English

Summary

1 Overview

1.1 Introduction

1.2 Web Server display and operating elements

Details the physical components and indicators of the Web Server.

1.3 User interface

Explains the graphical interface and its main navigation areas.

2 Commissioning

2.1 Prerequisites

Outlines the necessary conditions before starting the commissioning process.

2.2 Getting started

Guides on initial setup and powering up the Web Server.

2.2.1 Turn on Web Server

Guides on how to power up the Web Server and initial checks.

2.2.2 Log into Web Server

Details the procedure for logging into the Web Server interface.

2.4 Create device web pages

2.5 Web Server settings

Introduces the settings section for Web Server configuration.

2.5.3 Operating page Settings

2.5.3.3 Communication

Covers KNX communication settings, including device address and time sync.

Ethernet

Details Ethernet network configuration settings like DHCP, IP address, and DNS.

E-mail

Covers settings for sending emails, including address and authentication.

2.5.3.4 Message receivers

Describes how to configure message receivers for fault notifications.

2.5.3.8 Trend

2.5.3.9 Faults

Configures settings for sending fault notifications via email.

2.6 Commission network components

Explains how to connect and commission network components.

2.6.1 Access via portal

Explains how to access the Web Server via the Siemens Synco IC portal.

2.6.2 Access via a local area network (LAN)

Details how to access the Web Server via a local area network (LAN).

2.6.3 Access via direct connection

Explains how to establish a direct connection via the Internet.

2.7 Functional check

Guides on how to test the functionality of the Web Server and KNX devices.

2.9 Final steps

Details final checks and steps to complete the commissioning.

2.9.1 Check faults

Explains how to check for any pending faults before finalization.

2.9.2 Final steps on Web Server

Details final checks involving physical connections and LED status.

2.11 Software updates

Explains different types of software updates available for the Web Server.

3 Remote access via portal

3.1 Set up access via portal

Details the process of establishing remote access through the Siemens Synco IC portal.

4 Operate using a web browser

4.1 Overview

4.2 Operate the plant

Details how to operate the plant once it's ready for use.

4.2.1 Operate Synco device

Explains how to operate connected Synco devices via the Web Server.

4.2.2 Operate Web Server

Guides on operating the Web Server interface itself.

4.2.3 Web Server diagnostics

Shows how to access diagnostic information for the Web Server and KNX bus.

4.3 Faults

Provides an overview of the fault display and identification.

4.3.1 Overview

Provides an overview of the fault display and identification.

4.3.2 Device faults

Explains how to view detailed local faults for devices.

4.4 File transfer

7 Energy indicator function

7.1 Introduction

7.1.1 Function description

Explains how the Energy indicator works and its display logic.

7.2 Energy indicator function levels

7.2.1 Plant level

7.2.2 Partial plants level

7.2.3 Data points level

7.2.6 Summary display Energy indicator for a plant

7.3 Energy indicator commissioning function

Details the commissioning steps for the Energy indicator function.

7.3.1 Commissioning notes

7.3.2 Start Energy indicator function

7.3.4 Deactivating Data point monitoring

Describes how to deactivate data point monitoring for the Energy indicator.

7.3.5 Activating Data point monitoring

Explains how to reactivate data point monitoring for the Energy indicator.

7.4 Dialog boxes, data points, and Green limits

Explains how to work with dialog boxes, data points, and green limits.

7.4.1 General dialog boxes

7.4.2 Dialog boxes with numeric data points

7.4.3 Dialog boxes with enumeration data points

7.4.4 Dialog boxes with variable unit data points

7.4.5 Dialog boxes for data points with manually set value

7.5 E-mail with Energy indicator for the plant

7.5.1 E-mail receiver configuration

8 Communications

8.1 Remote operation

Introduces methods for remotely operating the Web Server.

8.1.1 Access via portal

8.1.2 Access via Local area network (LAN)

8.1.3 Access via direct connection

8.2 Messages via e-mail

9 Trend functions

9.1 Overview

9.2 Define trend

Guides on defining trends through the web interface.

9.2.1 Define trend via web

Guides on defining trends through the web interface.

9.2.4 Add trend data points

9.3 Send trend data by e-mail

9.3.1 Configure E-mail receiver

9.5 Graphical trend display

10 KNX S-Mode

S-mode

Supported properties

10.1 Configuration in KNX S-Mode

Details the configuration process for KNX S-Mode using ETS.

Data points

10.2 Operation KNX S-mode