To Next Page
G
Gary SchmittSep 9, 2025
Why "i-Dos ?/" cannot be actuated on my Siemens WM14XEH5GB?
- JJennifer HigginsSep 9, 2025
If "i-Dos ?/" cannot be actuated on your Siemens Washer, this is not a fault. Intelligent dosing is not intended for this programme.
Why "i-Dos ?/" cannot be actuated on my Siemens WM14XEH5GB?
If "i-Dos ?/" cannot be actuated on your Siemens Washer, this is not a fault. Intelligent dosing is not intended for this programme.
What to do if water is not flowing into my Siemens WM14XEH5GB Washer?
If water is not flowing into your Siemens Washer and detergent is not being dispensed, consider the following: * Ensure you have pressed Start/Reload. * The filter in the water inflow may be blocked. Clean the water inflow filter. * The tap may be turned off. Turn on the tap. * The water inlet hose could be kinked or jammed. Ensure that the water inlet hose is not kinked or jammed.
Why is water flushed under pressure into the detergent drawer of my Siemens WM14XEH5GB?
If water is flushed under pressure into the detergent drawer of your Siemens Washer, this is not a fault; it is a normal operating noise.
Why is high spin speed not reached on my Siemens WM14XEH5GB Washer?
If your Siemens Washer is not reaching high spin speeds, it could be due to: * A low spin speed being selected. Set a higher spin speed the next time you run a wash cycle. * Less Ironing being activated. Select the programmes that are suitable for the type of fabric.
Why is no water visible in the drum of my Siemens Washer?
If no water is visible in the drum of your Siemens Washer, this is not a fault. The water is below the visible area.
Why does the programme duration change during the wash cycle of my Siemens WM14XEH5GB Washer?
If the programme duration changes during the wash cycle of your Siemens Washer, this is not a fault. The programme operation is optimised electronically.
What to do if display goes out and Start/Reload flashes on Siemens WM14XEH5GB?
If the display of your Siemens Washer goes out and the Start/Reload button flashes, it means that the energy-saving mode is active. Press any button to exit this mode.
Why is laundry too wet after spin cycle in my Siemens WM14XEH5GB?
If the spin result is not satisfactory and your laundry is too wet or damp after using your Siemens Washer, consider the following: * A low spin speed may be selected. Set a higher spin speed for the next wash cycle. * Start the Spin programme. * Less Ironing may be activated. Select the programmes that are suitable for the type of fabric. * The drain pipe or water outlet hose may be blocked. Clean the drain pipe and the water outlet hose. * The drain pipe or water drain hose might be caught or jammed. Ensure that the drain pipe and water drain hose are not kinked or trapped. * The unbalanced load detection system may have interrupted the spin cycle because the laundry is unevenly distributed. Redistribute the laundry in the drum.
How to deal with heavy foam build-up in Siemens WM14XEH5GB Washer?
If you observe heavy foam build-up in your Siemens Washer: * As an immediate measure, mix one tablespoon of fabric softener with 0.5 litres of water and pour the mixture into the compartment for manual dosing (not for outdoor clothing, sportswear or items stuffed with down). * If intelligent dosing is activated, reduce the basic. * If you dose manually, reduce the amount of detergent for the next washing cycle with the same load.
How to prevent creasing in my Siemens WM14XEH5GB?
If your laundry is creased after washing in your Siemens Washer, it might be due to: * The spin speed being too high. Set a lower spin speed for the next wash cycle. * The load being too large. Reduce the amount of laundry being loaded for the next wash cycle. * Using an unsuitable programme for the type of fabric. Select the programmes that are suitable for the type of fabric.
General