Silicon Laboratories Si4010-C2 - User Manual

Rev. 1.0 2/11 Copyright © 2011 by Silicon Laboratories Si4010
Si4010-C2
CRYSTAL-LESS SOC RF TRANSMITTER
Features
Applications
Description
The Si4010 is a fully integrated crystal-less CMOS SoC RF transmitter with an
embedded CIP-51 8051 MCU. The device can operate over the –40 to 85
°C
temperature range without requiring an external crystal reference source reducing
board area and BOM cost. The device includes an 8
kB non volatile memory block
for programming the user's application along with a 12
kB ROM of embedded
support code for use in the user's application. The Si4010 includes Silicon
Laboratories' 2-wire C2 Debug and Programming interface, which allows
customers to download their code during the development stage into the on-board
RAM for testing and debug prior to programming the NVM.
The Si4010 is designed for low power battery applications with standby currents of
less than 10
nA to optimize battery life and features automatic wake on button
press support to efficiently move from the standby to active mode state with
minimal customer code support. Built in AES-128 hardware encryption along with
a 128-bit EEPROM can be used to create robust data encryption of the
transmitted packets. A unique 4-byte serial number is programmed into each
device ensuring non-overlapping device identifiers.
The RF transmitter features a high efficiency PA capable of delivering output
power up to +10
dBm and includes an automatic antenna tuning algorithm. This
algorithm adjusts the antenna tuning at the start of each packet transmission for
optimal output power minimizing the impact of antenna impedance changes due
to the remote being held in a user hand. The devices supports FSK and OOK
modulations and includes automatic output power shaping to reduce spectral
spreading and ease regulatory compliance. The output frequency can be adjusted
via software over the entire 27 to 960
MHz range. The output data rate is software
adjustable up to a maximum rate of 100
kbps.
 Crystal-less operation
Optional crystal oscillator input
 High-Speed 8051 µC Core
Pipeline instruction architecture
70% of instructions in 1 or 2 clocks
Up to 24 MIPs with 24 MHz clock
4 kB RAM/8kB NVM
128 bit EEPROM
256 byte of internal data RAM
12 kB ROM embedded functions
8 byte low leakage RAM
 Extensive Digital Peripherals
128 bit AES accelerator
5/9 GPIO with wakeup functionality
LED driver
Data serializer
High-speed frequency counter
On-chip debugging: C2
Unique 4 byte serial number
Ultra low-power sleep timer
 Single Coin-Cell Battery Operation
Supply voltage: 1.8 to 3.6 V
Standby current < 10 nA
 High-performance RF transmitter
Frequency range: 27–960 MHz
+10 dBm output power,
adjustable
Automatic antenna tuning
Symbol rate up to 100 kbps
FSK/OOK modulation
Manchester, NRZ, 4/5 encoder
 Analog Peripherals
LDO regulator with POR circuit
Battery voltage monitor
 Temperature range –40 to +85 °C
 Automotive quality option, 
AEC-Q100 (Pending final
qualification testing)
 10-pin MSOP/14-pin SOIC
 Garage and gate door openers
 Remote keyless entry
 Home automation and security
 Wireless remote controls
Patents pending
Ordering Information:
See page 15.
Pin Assignments
GPIO0/XTAL
Si4010-GT
2
3
6
7
8
4
5
9GPIO2
GPIO3
GPIO4
LEDVDD
TXP
GND
TXM
1 10 GPIO1
Si4010-GS
3
4
9
10
11
5
6
12 GPIO2
GPIO3
C2DAT/GPIO4
C2CLK/LEDVDD
VPP/GPIO0/XTAL
TXP
GND
TXM
2 13 GPIO1
GPIO9
1 14 GPIO8
87GPIO6GPIO7
14-Pin SOIC
10-Pin MSOP

Silicon Laboratories Si4010-C2 Specifications