Silvercrest SSB 36 A1 - Operating the Soundbar; Selecting Input Sources; Sound Settings; Bluetooth Connection

30
GB
6. Operation
NOTES:
• All adjustments can be conveniently carried out with
the remote control. The basic functions can also be car-
ried out with the buttons on the device. Operation of
the device in the instructions is usually described with
the remote control.
• The device switches to standby mode…
…if no Bluetooth connection is established within
20minutes or
…if it does not receive a signal for 20 minutes.
•Press the POWER 27 button to switch on the device
from standby mode.
6.1 Selecting the type of connection
1. Press one of the buttons AUX17, LINE IN26, OP-
TICAL16 or 14 to switch to the desired connection
(see “Connections” on page 29).
2. On the audio device you can now start playback and
select and control the music tracks.
NOTE: in order to use the optical input, you need to set
the output of your audio device to "PCM downmix".
6.2 Sound settings
NOTES:
• Changes to the sound settings are acknowledged with
brief flashing of the LED1, until the minimum/maxi-
mum value has been reached.
• Controlling the levels of the treble and bass is exclu-
sively possible in the "Music" settings, after pressing
the MUSIC18, button.
Controlling the volume
• During playback, press the VOLUME –/+  19 buttons.
Muting the device
1. Press MUTE15 to switch off the sound. The LED1
flashes.
2. To switch the sound back on, press MUTE again or
one of the VOLUME –/+19 buttons. The LED1
lights up.
Adjusting the tone quality
• Press one of the buttons18, to select the pre-sets for
the tone quality for music (MUSIC), films (MOVIE) or
language (DIALOG).
•Press the MUSIC18: button
-Use the TREBLE –/+25 buttons to adjust the treble
sounds.
-Use the BASS –/+21 buttons to adjust the bass
sounds.
6.3 Establishing a Bluetooth
connection
NOTES:
• The identification of the device is "SSB36A1".
• After it has been switched over to Bluetooth, the device
automatically attempts to establish a connection with
the last paired device.
• Please observe that the establishment process of the
connection may vary slightly depending on the device
and the software used.
1. Press the 14 button to switch over to a Bluetooth
connection. LED1 flashes blue.
2. Switch on the audio device (e.g. smartphone) and start
the Bluetooth connection.
3. Press the PAIR5 button on the device for approxi-
mately 1 second. The blue LED1 flashes rapidly. The
audio device will now receive the device identification
"SSB36A1".
4. Establish the connection with the soundbar on the au-
dio device. If you are asked for a password, enter
"0000". Both devices are now interconnected. LED1
now lights up in blue and a beep is heard.
NOTE: it is possible that audio devices remember the iden-
tification of the device. In this case, it may not be neces-
sary to establish the connection manually again if the
Bluetooth function is activated.
5. Now play a song on the audio device. The sound is
played back from the soundbar.
6. With the
I
WW
24, XX
I
20 and
X/
II
23 buttons you
can select and control the music tracks.
7. Cleaning and storing
DANGER! Risk of electric shock!
~ Pull the power unit7 out of the wall socket before you
clean the device. Make sure that no liquid gets into the
device.
• Clean the device with a slightly damp cloth. Solvents,
spirits, thinners etc. must not be used, as they can
damage the surface of the device.
• When not using the device, store it in a place where
neither high temperatures nor moisture can affect it.
Remove the battery from the remote control.
BB58B%ERRN6HLWH)UHLWDJ-XQL